<abstract xml:lang="en" xmlns="http://www.w3.org/1999/xhtml"> The main advantage of magnesium and its alloys is high specific strength and biocompatibility. A modern approach to magnesium-based materials preparation is powder metallurgy. This technique allows preparation of new materials with a unique structure, chemical composition, and controlled porosity. In this study, cold compaction of magnesium powder was studied. Magnesium powder of average particle size of 30 μm was compacted applying pressures of 100 MPa, 200 MPa, 300 MPa, 400 MPa and 500 MPa at laboratory temperature. Influence of compacting pressure was studied with microstructural and electrochemical corrosion characteristics analysis. The resulting microstructure was studied in terms of light and electron microscopy. Obtained electrochemical characteristics were compared with those of wrought magnesium. Compacting pressure had a significant influence on microstructure and electrochemical characteristics of prepared bulk magnesium. With the increase in compaction pressure, the porosity decreased. Compacting pressures of 300 MPa, 400 MPa and 500 MPa led to the similar microstructure of the prepared material. Polarization resistance of compacted magnesium was much lower and samples degraded faster when compared to wrought magnesium. Also, the corrosion degradation mechanism changed due to the microstructural differences between the material states.</abstract>

Evolution of microstructure and electrochemical corrosion characteristics of cold compacted magnesium

<abstract xml:lang="en" xmlns="http://www.w3.org/1999/xhtml"> The paper evaluates extent of corrosion damage to composite glass-fibre fabric reinforcement in environment simulating concrete pore solutions (pH 12.6, 13.0, 13.5) and carbonated concrete contaminated with chlorides (pH 8.1 + Cl-) using the FT-IR and SEM/EDS techniques. Also, the effect of corrosion damage on tensile strength of segmented glass fibre as well as the presence of specific protective organic coating on glass fibre were studied. The results demonstrate local corrosion damage of samples at pH 13.5 and on the other hand high stability in environment simulating carbonated concrete and carbonated concrete contaminated with chlorides. The study also suggests unevenness of organic coating with occurrence of localized porosity which is related to aforementioned corrosion damage. Corrosion damage in FT-IR spectra manifests by changes in peaks signalling hydrolysis of protective organic coating and occurrence of peaks suggesting presence of Ca2+ rich corrosion products.</abstract>

Study of damage extent to glass fibre in glass-fibre fabric reinforcement during exposure simulating concrete pore solution

<abstract xml:lang="en" xmlns="http://www.w3.org/1999/xhtml"> Carbon Capture and Storage (CCS) technologies are a perspective solution to reduce the amount of CO2 emissions. One of promising methods is Ca-looping, which is based on carbonation and calcination reactions. During both of these processes, especially calcination, high temperatures (650-950°C) are required. This means high demands on the corrosion resistance of equipment materials. Therefore, we carried out a study to suggest materials with suitable properties for calciner construction, which have to be particularly heat resistant: stainless steels (AISI 304, AISI 316L and AISI 316Ti) and nickel alloys (Inconel 713, Inconel 738, Incoloy 800H). A special device simulating calciner environment was built for this purpose. Chosen materials were tested in temperature 900°C, atmospheric pressure and gaseous environment with composition that can be possible in a calciner. The surfaces of materials were evaluated to determine composition and properties of formed oxide layers. High temperature oxidation was observed on all tested materials and oxide exfoliation occurred on some of tested materials (304, 316L).</abstract>

Materials for use in calcium looping technology for CCS – corrosion processes in high-temperature CO2

<abstract xml:lang="en" xmlns="http://www.w3.org/1999/xhtml"> In the present study, we investigated the influence of hammer peening (HP) with tungsten carbide surface coating (WCSC) on high cycle bending fatigue performance of the carbon steel (CS) manufactured as specified in Bureau of Indian Standards BIS 2062 steel. Totally there are twenty-four numbers of specimens cast and tested to investigate fatigue performance. Constantly high cycle bending fatigue load (HBFL) were applied for all specimen, different range of bending stress applied to the specimen and the stress ratio maintained as R = 1. Investigation results show there is up to 40 percent of the fatigue life improvement possible by the surface treatments to the CS material. From the research to date the corrosion and pitting corrosion can be treated by modifying the surface layer of the metal by treating different peening methods and coating.</abstract>

Effect of hammer peening with tungsten coating on fatigue properties of carbon steel under rotating bending

<abstract xml:lang="en" xmlns="http://www.w3.org/1999/xhtml"> An overview of protection mechanisms of organic coatings for metallic constructions and products is given. The barrier effect of coatings and protection in local defects are discussed. Basic degradation mechanisms of organic coatings such as anodic and cathodic delamination in vicinity of defects, osmotic and cathodic blistering, mechanical stress assisted blistering, loss of adhesion and chalking are described. Appropriate laboratory tests are proposed for each degradation mode.</abstract>

Mechanisms of degradation of organic coatings

AHEAD OF PRINT

Volume 68 (2024): Issue 1 (March 2024)

Volume 67 (2023): Issue 1 (May 2023)

Volume 66 (2022): Issue 1 (January 2022)

Volume 65 (2021): Issue 4 (December 2021)

Volume 65 (2021): Issue 3 (November 2021)

Volume 65 (2021): Issue 2 (September 2021)

Volume 65 (2021): Issue 1 (May 2021)

Volume 64 (2020): Issue 4 (December 2020)

Volume 64 (2020): Issue 3 (October 2020)

Volume 64 (2020): Issue 2 (June 2020)

Volume 64 (2020): Issue 1 (March 2020)

Volume 63 (2019): Issue 4 (December 2019)

Volume 63 (2019): Issue 3 (November 2019)

Volume 63 (2019): Issue 2 (June 2019)

Volume 63 (2019): Issue 1 (March 2019)

Volume 62 (2018): Issue 4 (December 2018)

Volume 62 (2018): Issue 3 (July 2018)

Volume 62 (2018): Issue 2 (May 2018)

Volume 62 (2018): Issue 1 (February 2018)

Volume 61 (2017): Issue 5 (December 2017)

Volume 61 (2017): Issue 4 (October 2017)

Volume 61 (2017): Issue 3 (July 2017)

Volume 61 (2017): Issue 2 (April 2017)

Volume 61 (2017): Issue 1 (March 2017)

Volume 60 (2016): Issue 5 (December 2016)

Volume 60 (2016): Issue 4 (December 2016)

Volume 60 (2016): Issue 3 (September 2016)

Volume 60 (2016): Issue 2 (June 2016)

Volume 60 (2016): Issue 1 (March 2016)

Volume 59 (2015): Issue 4 (December 2015)

Volume 59 (2015): Issue 3 (November 2015)

Volume 59 (2015): Issue 2 (July 2015)

Volume 59 (2015): Issue 1 (April 2015)

Volume 58 (2014): Issue 4 (December 2014)

Volume 58 (2014): Issue 3 (November 2014)

Volume 58 (2014): Issue 2 (June 2014)

Volume 58 (2014): Issue 1 (March 2014)

Volume 57 (2013): Issue 4 (December 2013)

Volume 57 (2013): Issue 3 (September 2013)

Volume 57 (2013): Issue 2 (June 2013)

Volume 57 (2013): Issue 1 (March 2013)

Volume 56 (2012): Issue 4 (December 2012)

Volume 56 (2012): Issue 3 (October 2012)

Volume 56 (2012): Issue 2 (July 2012)

Volume 56 (2012): Issue 1 (March 2012)

Koroze a ochrana materiálu

The journal is primarily focused on corrosion engineering and surface treatment of metallic materials. We accept also articles concerning degradation of paints, enamels and other non-metallic materials used for corrosion prevention of metals. Another field of interest is conservation and restoration of cultural heritage. In this case we accept contributions concerning all materials (metals, wood, paper, leather, textiles, stone, glass and ceramics).  Why subscribe and read   Official Journal of the Association of Czech and Slovak Corrosion Engineers, premier source of high quality research results from all over the world with special emphasis on Central and Eastern Europe;  over 55 years of experience in publishing original papers dealing with corrosion science, engineering and technology;  focused on research in corrosion and surface treatment as well as experiences in practice and „case studies“;  original papers that advance understanding of both the fundamentals of corrosion and its application;  excellent articles authored by researchers from all over the world, who appreciate our fast, fair and constructive peer review provided by experts in the field of corrosion engineering.   Why submit   Fast, fair and constructive peer review  Fast publication process („submission→published article“ takes usually 3-6 months)  High quality electronic publication technologies  Open access (simple and charge-free access for every researcher)   Rejection Rate   10%   Archiving  Sciendo archives the contents of this journal in Portico - digital long-term preservation service of scholarly books, journals and collections.  Plagiarism Policy  The editorial board is participating in a growing community of Similarity Check System's users in order to ensure that the content published is original and trustworthy. Similarity Check is a medium that allows for comprehensive manuscripts screening, aimed to eliminate plagiarism and provide a high standard and quality peer-review process. 

Koroze a ochrana materiálu

Volume 61 (2017): Issue 4 (October 2017)

Evolution of microstructure and electrochemical corrosion characteristics of cold compacted magnesium

Study of damage extent to glass fibre in glass-fibre fabric reinforcement during exposure simulating concrete pore solution

Materials for use in calcium looping technology for CCS – corrosion processes in high-temperature CO₂

Effect of hammer peening with tungsten coating on fatigue properties of carbon steel under rotating bending

Mechanisms of degradation of organic coatings

Wyszukiwanie

Wszystkie tomy i zeszyty w tym czasopiśmie