<abstract xmlns="http://www.w3.org/1999/xhtml">Lead is a heavy metal with strong toxic properties. This chemical element is found in wastewater and sometimes in drinking water. The article deals with the removal of lead(II) ions from polluted water using a sorption process to determine the most effective sorbent for the removal of lead(II) ions. Three sorbents were used in the research: clay, sapropel, and iron sludge. All three sorbents investigated reduce the concentration of lead(II) ions in water: clay efficiency was of 65.7–90 %, sapropel of 94.3–100 %, and iron sludge of 84.3–97 %, depending on sorbent type and contact duration. The research has shown that the most effective way to remove lead(II) ions from the test water is sapropel. Using different amounts of sapropel (1, 2, 3, 4, 5, 6 g/dm3 and 0.1, 0.2, 0.4, 0.5, 0.6, 0.8 g/dm3) and different duration of contact (30, 60, 90, 120 and 150 minutes), the concentration of lead(II) ions in the test water after purification did not exceed the permissible values for drinking water (10 μg/dm3), so that the lowest sapropel content of 0.1 g/dm3 can be used for sorption. Lead(II) ions are most effectively removed when contact time is 30 min.</abstract>

Lead is a heavy metal with strong toxic properties. This chemical element is found in wastewater and sometimes in drinking water. The article deals with the removal of lead(II) ions from polluted water using a sorption process to determine the most effective sorbent for the removal of lead(II) ions. Three sorbents were used in the research: clay, sapropel, and iron sludge. All three sorbents investigated reduce the concentration of lead(II) ions in water: clay efficiency was of 65.7–90 %, sapropel of 94.3–100 %, and iron sludge of 84.3–97 %, depending on sorbent type and contact duration. The research has shown that the most effective way to remove lead(II) ions from the test water is sapropel. Using different amounts of sapropel (1, 2, 3, 4, 5, 6 g/dm3 and 0.1, 0.2, 0.4, 0.5, 0.6, 0.8 g/dm3) and different duration of contact (30, 60, 90, 120 and 150 minutes), the concentration of lead(II) ions in the test water after purification did not exceed the permissible values for drinking water (10 μg/dm3), so that the lowest sapropel content of 0.1 g/dm3 can be used for sorption. Lead(II) ions are most effectively removed when contact time is 30 min.

Investigation of Lead Removal from Drinking Water Using Different Sorbents

Department of Chemistry and Bioengineering, Faculty of Fundamental Sciences

Department of Environmental Protection and Water Engineering, Faculty of Environmental Engineering

Ecological Chemistry and Engineering S

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

{"article-title":"Investigation of Lead Removal from Drinking Water Using Different Sorbents"}

Lead is a heavy metal with strong toxic properties. This chemical element is found in wastewater and sometimes in drinking water. The article deals with the...

Investigation of Lead Removal from Drinking Water Using Different Sorbents

Data publikacji: 24 kwi 2020

Zakres stron: 67 - 82

DOI: https://doi.org/10.2478/eces-2020-0004

Słowa kluczowe
lead, water, sorbent, adsorption, clay, sapropel, water treatment iron sludge

© 2020 Ramunė Albrektienė et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Investigation of Lead Removal from Drinking Water Using Different Sorbents

Data publikacji: 24 kwi 2020

Zakres stron: 67 - 82

DOI: https://doi.org/10.2478/eces-2020-0004

Słowa kluczowelead, water, sorbent, adsorption, clay, sapropel, water treatment iron sludge

© 2020 Ramunė Albrektienė et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Słowa kluczowe
lead, water, sorbent, adsorption, clay, sapropel, water treatment iron sludge