<abstract><title style='display:none'>Abstract</title>Rice Husk Ash (RHA) is a well-known supplementary cementitious materials (SCMs) that can be used for concrete with reduced CO2 contributions. In 2016, only Nepal produced 5.2 million tonnes rice that gave about 1.14 million tonnes rice husk. The rice husk can also be used directly in a cement kiln as a fuel. This study analysis the potential CO2 reductions from three scenarios and emphasis strengths, weaknesses, opportunities and treats in the production systems for initiate a decision process with possibilities to get an industry project financed from the green climate found. The highest CO2 benefits were from rice husk used in a cement kiln were half of the yearly rice husk production in Nepal could reduce the climate impact with 808000 tonnes CO2.</abstract>

Rice Husk Resource for Energy and Cementitious Products with Low CO2 Contributions

<abstract><title style='display:none'>Abstract</title>Hydrated Portland cement paste exposed to a NaCl solution was acidified by adding HCl in small steps, gradually lowering the pH. The chloride binding of the cement paste changed as a function of the pH. For the range of pH from 13.2 to 12.2, decreasing pH resulted in a considerable increase in the chloride binding. At a pH of 11, the cement paste showed almost no chloride binding. In order to explain the changes in chloride binding upon lowering the pH, the phase assemblage was investigated with SEM-EDS, TGA and XRD and compared to a thermodynamic modelling.</abstract>

Towards the Understanding of the pH Dependency of the Chloride Binding of Portland Cement Pastes

<abstract><title style='display:none'>Abstract</title>In the planned Swedish repository for spent nuclear fuel, plugs are designed to close the deposition tunnels. The outer part of these plugs consists of a concrete dome made with self-compacting-concrete, designed to have low pH to reduce negative effects on the bentonite clay buffer. A full-scale test has been performed to evaluate the performance of the plug, to test the installation and to verify underlying design assumptions. In this paper, the behaviour of the concrete dome is evaluated based on measurements, from casting the concrete until it was subjected to 4 MPa hydrostatic water pressure.</abstract>

Full-scale Test of an Unreinforced Concrete Dome Plug for the Spent Nuclear Fuel Repository

<abstract><title style='display:none'>Abstract</title>In the studies for crossing the long and deep Norwegian fjords along the E39 road, on the west coast of Norway, some challenging structures have been evaluated. Some of them are known structures, like floating bridges, and some others are structures never built before, like suspension bridges on tension leg platforms and submerged floating tube bridges. In the development of the feasibility studies for these crossings, the choice of materials has played an important role. The materials influence not only the design and the cost, but also the behaviour of the structure towards the environmental loads and some particular loads as the ship collision. The article illustrates the different solutions proposed for the fjord crossings and discusses the influence in the choice of the material, with special regards to the type of concrete. The pros and cons of the application of the light weight concrete are discussed.</abstract>

Engineer for Norwegian Public Road Administration Østensjøveien 34,

Senior Engineer for Norwegian Public Road Administration Brynsengfaret 6A,

Chief Engineer for Norwegian Public Road Administration Parkgata 81,

Chief Engineer for Norwegian Public Road Administration Abels Gate 5,

The Choice of Materials for the E39 Fjord Crossing Project

<abstract><title style='display:none'>Abstract</title>Well-known frost destruction mechanisms applicable to concrete not exposed to salt are, (1) hydraulic pressure during freezing, (2) growth of ice-bodies in capillaries during freezing. Theories behind these mechanisms are presented. A third mechanism, ice expansion during heating of frozen concrete, is put forward. The validity of a certain mechanisms is discussed by analyzing its ability to explain experimental observations.</abstract>

Frost Destruction of Concrete – A Study of the Validity of Different Mechanisms

<abstract><title style='display:none'>Abstract</title>Knowledge of the elastic properties of concrete at early age is often a pre-requisite for numerical calculations. This paper discusses the use of a laboratory technique for determining Poisson’s ratio at early concrete age. A non-destructive test set-up using the impact resonance method has been tested and evaluated. With the method, it has been possible to obtain results already at 7 hours of concrete age. Poisson’s ratio is found to decrease sharply during the first 24 hours to reach a value of 0.08 and then increase to approximately 0.15 after seven days.</abstract>

Dynamic Measurements for Determining Poisson’s Ratio of Young Concrete

<abstract>
<title style='display:none'>Abstract</title>
Pumping is the preferred placement method for concrete. The pumping process influences fresh properties of concrete. Competent producers handle these issues when composing the mix design. However, sudden changes in workability sometimes appear, both in the form of increased and decreased workability. Both changes might be handled on-site. However, even the situations that are sufficiently handled, cause delays and extra costs. Sometimes the final result’s quality is compromised, resulting in repairs and economic compensation claims. The extent and causes of incidents with sudden changes in workability are still to be investigated.
It is suggested that around 1 100 000 m3 or 30% of concrete experience sudden change in workability annually in Norway, and that 200 000 kg of chemical admixtures is used on-site. It appears that the most relevant cause is to find within variations in the fine aggregate. Increase in workability might also be caused by lack of compatibility between superplasticiser and binding materials in low-carbon concrete, enhanced by the extra mixing process caused by the pumping process.
To approach these questions, the Quality Assessment system of a medium-sized Norwegian concrete producer has been investigated. It comprises documentation of 1 500 000 m3 of concrete, over 10 years.
</abstract>

Sudden Changes in Workability during Concrete Pumping – An Industrial Approach

<abstract>
<title style='display:none'>Abstract</title>
This study investigates the links between the non-steady-state chloride migration coefficient, the bulk electrical conductivity and the formation factor of blended cement paste specimens. 18 different binders were tested: two Portland cements (low- and high-alkali) in combination with limestone filler, fly ash, calcined clay, two biomass ashes, sewage sludge ash and crushed brick, as well as two Portland composite cements. In addition, the latter and the low-alkali Portland cement were tested in concrete as well for comparison.
Mixes with high-alkali cement showed better resistance to chloride transport, and the effect of supplementary cementitious materials was found to be strongly linked with their reactivity. Moreover, the results showed a clear correlation of the migration coefficient with the bulk electrical conductivity and, to a lesser extent, with the formation factor. However, these relationships are strongly influenced by the methods used to determine conductivities and they need to be validated for higher maturities. Finally, the results suggested a fairly good correspondence between the results obtained on paste and concrete.
</abstract>

Relationship between Chloride Migration, Bulk Electrical Conductivity and Formation Factor of Blended Cement Pastes

<abstract>
<title style='display:none'>Abstract</title>
In concrete structures, material performance is typically determined at the level of the concrete mix (the microscale) and the overall shape and dimensions of a building element (the macroscale). However, recent developments in the field of 3D Concrete Printing (3DCP) are demonstrating that the design of concrete now also can take place at a previously impossible intermediate scale involving the shaping and placement of the material at the level of the printing nozzle (the mesoscale). By focusing directly on the design of print paths, advanced surface effects and internal porous material distributions can be achieved that significantly affect the aesthetic experience and structural performance of 3DCP structures. This ability to design the distribution of concrete according to local architectural, structural, and functional design criteria is an especially interesting application of 3DCP that could be exploited to customise material performance while at the same time optimising material use and reducing the self-weight of building elements. This paper specifically examines how four different three-dimensional print patterns produce distinct material structures at the mesoscale (mesostructures) and presents an experimental procedure for evaluating their load-bearing capacity.
</abstract>

Towards the Application of Mesostructures in 3D Concrete Printing – Evaluating Load-bearing Performance

Preface

<abstract>
<title style='display:none'>Abstract</title>
Concrete cover is the thickness of the concrete layer that protects the reinforcing steel bars (rebar) within a reinforced concrete structure. It acts as a barrier against external elements such as moisture, chemicals, and environmental factors, safeguarding the rebar from corrosion. Concrete cover measurement is performed by using various nondestructive tests such as GPS (Ground Penetrating Radar), electromagnetic test and ultrasonic. The main benefit of the concrete cover thickness measurement is to explain the causes of corrosion and identify areas that have the capability to corrode faster.
This paper discusses the possibilities to measure the concrete cover depth and determine the location of steel bars of a thick-walled concrete structure by using different nondestructive testing methods. The methods studied are a concrete cover meter, Ground Penetrating Radar, which is based on propagation radar waves in concrete, and Ultrasonic Pulse Echo tomography based on stress waves produced by ultrasonic pulses. The paper demonstrates the use of these methods for in-situ measurements on a thick-walled reinforced concrete structure. The concrete cover depth and the location for the reinforcement bars received by different methods are compared and the strong and weak points of the methods are discussed.
The results indicate that the concrete cover meter is suitable for measuring the thickness of concrete cover, while the Ground Penetrating Radar and the Ultrasonic Pulse Echo device were able to identify and locate the reinforcement bars position in the concrete structure.
</abstract>

Determining the Location of Steel Reinforcement in Thick Concrete Walls by Non-Destructive Inspection

<abstract>
<title style='display:none'>Abstract</title>
Accelerated carbonation of recycled concrete aggregates (RCA) could be an efficient way to reduce the carbon footprint. High CO2-concentration under optimal relative humidity could accelerate the CO2 binding capacity of the hydrated cement paste in the RCA. The latter is the topic of this paper. The study looks into the forced carbonation of crushed cement pastes as a basis to understand the CO2 uptake in relation to various binders containing supplementary cementitious materials (SCM) such as fly ash (FA) and ground granulated blast furnace slag (GGBS). Samples include three cement pastes: ordinary Portland cement, substitution rate of 30 % FA and 50 % GGBS respectively at a water/binder ratio of 0.45. All binders were graded to 0/2, 2/4 and 4/8 mm fraction sizes and preconditioned before exposed to CO2 concentration of 10 % under controlled temperature at 20 °C and 65 % RH. All tested binders presented a high CO2 uptake within the first hours of exposure with clear differences concerning the fraction sizes and the composition. The phase content before and after carbonation was observed by X-ray diffraction and the portlandite and calcite were quantified by thermogravimetric analyses and their derivative curves for fraction size 4/8 mm.
</abstract>

Accelerated Carbonation of Binders Containing SCM at High CO2 Concentration

<abstract>
<title style='display:none'>Abstract</title>
Marine sediments can be stabilized by ultra high-strength binders: cement, Cement Kiln Dust (CKD) and slag. The properties of the stabilized soil indicate potential to their reuse. This study investigated the performance of the unconfined compressive strength (UCS) in the marine sediments stabilized by binder (cement, CKD, slag), tested by ultrasonic P-waves. Materials include 194 specimens collected from the port of Gothenborg. The experiment was performed in Swedish Geotechnical Institute (SGI). The UCS of specimens stabilized by different ratio of binders (cement, CKD, slag) was tested by resonance frequencies of the elastic P-waves. The significant increase in the UCS (&gt;1500 kPa) was recorded for the highest values of CKD and cement, and low values of slag. The correlation profiles of low water/high binder (LW/HB) cement/slag (40/60%) were controlled by curing time. The slag–cement–CKD simplex tests demonstrated UCS of samples with low/high water content and various binder ratio of cement (kg/m3). The ratio of cement binder and curing time play a critical role in the increase of UCS followed by mechanical properties of specimens and intensity of stress. The highest values exceed 1000 m/s in P-waves. The results shown high accuracy (97%) and non-contacting approach for testing UCS of sediments. Seismic methods can be applied to test the UCS of the stabilized sediments, and also <italic>in-situ</italic> via seismic CPT, surface testing or cross hole seismic testing.
</abstract>

Resonant Frequency Ultrasonic P-Waves for Evaluating Uniaxial Compressive Strength of the Stabilized Slag–Cement Sediments

<abstract><title style='display:none'>Abstract</title>Air contents of concrete are necessary for concrete durability in freeze-thaw exposure. According to the Finnish concrete code, the target value for air content varies between 4% and 5.5% for XF - exposure classes. Lately in Finland, some cases showed an elevation of air contents up to 15% in fresh air-entrained concrete at construction site and in drilled concrete samples.The objectives of this study were to investigate the stability of air entrainment by measuring the air content elevation 30 minutes and 60 minutes after concrete mixing and investigating the concrete sensitivity to segregation. Composition of concretes used in this study include 7 different combination of PCE based superplasticizer and air-entraining agent admixtures, cement content of 425 kg/m3, two consistency classes S3 with water to cement ration of 0.33 and F5 with water to cement ration of 0.38. One cement type was used for all concrete mixes. The concretes were mixed for 2 minutes and 5 minutes mixing times.The results show that the elevation of the air content of fresh concrete depends on the consistency of the concrete and on the used combination of superplasticizer and air-entraining agents. The higher consistency classes concretes have more risk of air elevation with some combinations of PCE-based superplasticizers and air-entraining agents. The results also indicate that short mixing time would not be enough to achieve total effectivity of some air-entraining agents, especially for higher consistency classes concrete.</abstract>

Stability of Air Content in Fresh Concretes with PCE-Based Superplasticizers

<abstract><title style='display:none'>Abstract</title>Crack formation in concrete structures due to various load and non-load factors leading to degradation of service life is very common. Repair and maintenance operations are, therefore, necessary to prevent cracks propagating and reducing the service life of the structures. Accessibility to affected areas can, however, be difficult as the reconstruction and maintenance of concrete buildings are expensive in labour and capital. Autonomous healing by encapsulated bacteria-based self-healing agents is a possible solution. During this process, the bacteria are released from a broken capsule or triggered by water and oxygen access. However, its performance and reliability depend on continuous water supply, protection against the harsh environment, and densification of the cementitious matrix for the bacteria to act. There are vast methods of encapsulating bacteria and the most common carriers used are: encapsulation in polymeric materials, lightweight aggregates, cementitious materials, special minerals, nanomaterials, and waste-derived biomass. Self-healing efficiency of these encapsulated technologies can be assessed through many experimental methodologies according to the literature. These experimental evaluations are performed in terms of quantification of crackhealing, recovery of durability and mechanical properties (macro-level test) and characterization of precipitated crystals by healing agent (micro-level test). Until now, quantification of crack-healing by light microscopy revealed maximum crack width of 1.80mm healed. All research methods available for assesing self-healing efficiency of bacteria-based healing agents are worth reviewing in order to include a coherent, if not standardized framework testing system and a comparative evaluation for a novel incorporated bacteria-based healing agent.</abstract>

Encapsulation Techniques and Test Methods of Evaluating the Bacteria-Based Self-Healing Efficiency of Concrete: A Literature Review

Authors Checklist

Authors Instructions

Nordic Concrete Research

 The aim is to publish reviewed papers on research, recent experiences, and education within the broad concrete field. The scope covers all aspects of concrete and other...

Impact Factor

Five Year Impact Factor

MNiSW

 The aim is to publish reviewed papers on research, recent experiences, and education within the broad concrete field. The scope covers all...