<abstract xmlns="http://www.w3.org/1999/xhtml">Magnesium and its alloys are perspective bio-degradable materials used mainly due to their mechanical properties similar to those of mammal bones. Potential problems in utilization of magnesium alloys as bio-materials may relate to their rapid degradation which is associated with resorption problems and intensive hydrogen evolution. These problems can be eliminated by magnesium alloys surface treatment. Therefore, this work aims with analysis of the influence of fluoride conversion coating on corrosion characteristics of magnesium alloy. Unconventional technique by insertion of wrought magnesium alloy AZ61 into molten Na[BF4] salt at temperature of 450 °C at different treatment times was used for fluoride conversion coating preparation. The consequent effect of the coating on magnesium alloy corrosion was analyzed by means of linear polarization in simulated body fluid solution at 37 ± 2 °C. The obtained results prove that this method radically improve corrosion resistance of wrought AZ61magnesium alloy even in the case of short time of coating preparation.</abstract>

Vysoké učení technické v Brně, Fakulta chemická, Ústav materiálů

Žilinská univerzita v Žiline, Výskumné centrum Žilinskej univerzity

Ústav fyziky materiálů AV ČR v. v. i., Brno

Vysoké učení technické v Brně, Fakulta strojního inženýrství

Improvement of bio-compatible AZ61 magnesium alloy corrosion resistance by fluoride conversion coating

<abstract xmlns="http://www.w3.org/1999/xhtml">This study is focused on an influence of heat transfer on corrosion behaviour of structural materials for radioactive waste canister in synthetic bentonite pore water and bentonite suspension. Experiments were carried out in special cell on cylindrical sample of carbon steel, copper, titanium-palladium alloy and two types of stainless steel. Samples were subjected in synthetic bentonite pore water to sixty-fold higher heat transfer compared to real repository, and approximately thirty-fold higher in bentonite suspension. Corrosion behaviour was observed in two-electrode setup with platinum wire as counter electrode by means of electrochemical impedance spectroscopy. Results showed negligible effect of heat transfer compared to surface temperature.</abstract>

VŠCHT Praha, Ústav kovových materiálů a korozního inženýrství

Influence of heat transfer on corrosion behaviour of materials for radioactive waste canisters in synthetic bentonite pore water and bentonite suspension

<abstract xmlns="http://www.w3.org/1999/xhtml">In this work, the main aim is focused on the decomposition products of film-forming amines which are used as corrosion protection of devices against surface corrosion at frequent short outages. Filming amines are a mixture of volatile alkaline and contact organic amines, which protect both the water and the steam environment. It was confirmed, the organic matter is not stable at high temperature and decomposes to organic acids with short chain (acetic, formic) which decrease pH value and increase conductivity value.</abstract>

Study of decomposition products of film forming amines under conditions of 570°C and 17 MPa

<abstract xmlns="http://www.w3.org/1999/xhtml">The article is aimed at evaluation of chosen properties of thermally sprayed coatings based on tungsten carbide. It was evaluated two types of coatings – WC-FeCrAl and WC-WB-Co. The coatings were deposited on basic material steel AISI 316L. The aim of experimental works was to determine the quality and resistance of coatings in corrosion environment depending on number of thermal cycles. The quality of coatings was evaluated by determination of their adhesion depending on thermal cycles, determination of microhardness and indentation fracture toughness. Coatings were exposed in tribo-corrosion conditions with the presence of 1% NaCl. The results of experimental showed a higher quality of coating WC-WB-Co.</abstract>

Determination of selected properties and fracture toughness of HVOF coatings

<abstract xmlns="http://www.w3.org/1999/xhtml">Clinching is a joining method in which sheet metal parts are deformed locally by creating a mechanical interlock without the use of any additional elements such as screws or rivets. Steel sheets are plastically deformed and the shape of the tools remains theoretically unchanged during the clinching process. The clinching tool with a rigid die of ø5 mm with a specially formed gap and a punch of ø3.6 mm were used for mechanical joining of hot-dip galvanized dual-phase steel sheets HCT600X of 0.8 mm thickness. The punch and die were deposited by PVD coating of CrN and TiCN type with LARC technology. The state of the coating was evaluated and documented by scanning electron microscopy – SEM. The wear of the coating was evaluated after each 50 manufactured joints starting with the initial state of tool.</abstract>

Wear of PVD coated tools for joining by clinching method

AHEAD OF PRINT

Volume 68 (2024): Issue 1 (March 2024)

Volume 67 (2023): Issue 1 (May 2023)

Volume 66 (2022): Issue 1 (January 2022)

Volume 65 (2021): Issue 4 (December 2021)

Volume 65 (2021): Issue 3 (November 2021)

Volume 65 (2021): Issue 2 (September 2021)

Volume 65 (2021): Issue 1 (May 2021)

Volume 64 (2020): Issue 4 (December 2020)

Volume 64 (2020): Issue 3 (October 2020)

Volume 64 (2020): Issue 2 (June 2020)

Volume 64 (2020): Issue 1 (March 2020)

Volume 63 (2019): Issue 4 (December 2019)

Volume 63 (2019): Issue 3 (November 2019)

Volume 63 (2019): Issue 2 (June 2019)

Volume 63 (2019): Issue 1 (March 2019)

Volume 62 (2018): Issue 4 (December 2018)

Volume 62 (2018): Issue 3 (July 2018)

Volume 62 (2018): Issue 2 (May 2018)

Volume 62 (2018): Issue 1 (February 2018)

Volume 61 (2017): Issue 5 (December 2017)

Volume 61 (2017): Issue 4 (October 2017)

Volume 61 (2017): Issue 3 (July 2017)

Volume 61 (2017): Issue 2 (April 2017)

Volume 61 (2017): Issue 1 (March 2017)

Volume 60 (2016): Issue 5 (December 2016)

Volume 60 (2016): Issue 4 (December 2016)

Volume 60 (2016): Issue 3 (September 2016)

Volume 60 (2016): Issue 2 (June 2016)

Volume 60 (2016): Issue 1 (March 2016)

Volume 59 (2015): Issue 4 (December 2015)

Volume 59 (2015): Issue 3 (November 2015)

Volume 59 (2015): Issue 2 (July 2015)

Volume 59 (2015): Issue 1 (April 2015)

Volume 58 (2014): Issue 4 (December 2014)

Volume 58 (2014): Issue 3 (November 2014)

Volume 58 (2014): Issue 2 (June 2014)

Volume 58 (2014): Issue 1 (March 2014)

Volume 57 (2013): Issue 4 (December 2013)

Volume 57 (2013): Issue 3 (September 2013)

Volume 57 (2013): Issue 2 (June 2013)

Volume 57 (2013): Issue 1 (March 2013)

Volume 56 (2012): Issue 4 (December 2012)

Volume 56 (2012): Issue 3 (October 2012)

Volume 56 (2012): Issue 2 (July 2012)

Volume 56 (2012): Issue 1 (March 2012)

KOM – Corrosion and Material Protection Journal

The journal is primarily focused on corrosion engineering and surface treatment of metallic materials. We accept also articles concerning degradation of paints, enamels and other non-metallic materials used for corrosion prevention of metals. Another field of interest is conservation and restoration of cultural heritage. In this case we accept contributions concerning all materials (metals, wood, paper, leather, textiles, stone, glass and ceramics).  Why subscribe and read   Official Journal of the Association of Czech and Slovak Corrosion Engineers, premier source of high quality research results from all over the world with special emphasis on Central and Eastern Europe;  over 55 years of experience in publishing original papers dealing with corrosion science, engineering and technology;  focused on research in corrosion and surface treatment as well as experiences in practice and „case studies“;  original papers that advance understanding of both the fundamentals of corrosion and its application;  excellent articles authored by researchers from all over the world, who appreciate our fast, fair and constructive peer review provided by experts in the field of corrosion engineering.   Why submit   Fast, fair and constructive peer review  Fast publication process („submission→published article“ takes usually 3-6 months)  High quality electronic publication technologies  Open access (simple and charge-free access for every researcher)   Rejection Rate   10%   Archiving  Sciendo archives the contents of this journal in Portico - digital long-term preservation service of scholarly books, journals and collections.  Plagiarism Policy  The editorial board is participating in a growing community of Similarity Check System's users in order to ensure that the content published is original and trustworthy. Similarity Check is a medium that allows for comprehensive manuscripts screening, aimed to eliminate plagiarism and provide a high standard and quality peer-review process. 