<abstract xmlns="http://www.w3.org/1999/xhtml"><p>Within the framework of the project for design and optimization of the Remotely Operated Vehicle (ROV), research on its propulsion has been carried out. Te entire project was supported by CFD and FEM calculations taking into account the characteristics of the underwater vehicle. One of the tasks was to optimize the semi-open duct for horizontal propellers, which provided propulsion and controllability in horizontal plane. In order to create a measurable model of this task it was necessary to analyze numerical methodology of propeller design, along with the structure of a propellers with nozzles and contra-rotating propellers. It was confronted with theoretical solutions which included running of the analyzed propeller near an underwater vehicle. Also preliminary qualitative analyses of a simplified system with contra-rotating propellers and a semi-open duct were carried out. Te obtained results enabled to make a decision about the ROVs duct form. Te rapid prototyping SLS (Selective Laser Sintering) method was used to fabricate a physical model of the propeller. As a consequence of this, it was necessary to verify the FEM model of the propeller, which based on the load obtained from the CFD model. Te article contains characteristics of the examined ROV, a theoretical basis of propeller design for the analyzed cases, and the results of CFD and FEM simulations.</p></abstract>

Within the framework of the project for design and optimization of the Remotely Operated Vehicle (ROV), research on its propulsion has been carried out. Te entire project was supported by CFD and FEM calculations taking into account the characteristics of the underwater vehicle. One of the tasks was to optimize the semi-open duct for horizontal propellers, which provided propulsion and controllability in horizontal plane. In order to create a measurable model of this task it was necessary to analyze numerical methodology of propeller design, along with the structure of a propellers with nozzles and contra-rotating propellers. It was confronted with theoretical solutions which included running of the analyzed propeller near an underwater vehicle. Also preliminary qualitative analyses of a simplified system with contra-rotating propellers and a semi-open duct were carried out. Te obtained results enabled to make a decision about the ROVs duct form. Te rapid prototyping SLS (Selective Laser Sintering) method was used to fabricate a physical model of the propeller. As a consequence of this, it was necessary to verify the FEM model of the propeller, which based on the load obtained from the CFD model. Te article contains characteristics of the examined ROV, a theoretical basis of propeller design for the analyzed cases, and the results of CFD and FEM simulations.

CFD and FEM Model of an Underwater Vehicle Propeller

Polish Maritime Research

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

{"article-title":"CFD and FEM Model of an Underwater Vehicle Propeller"}

Within the framework of the project for design and optimization of the Remotely Operated Vehicle (ROV), research on its propulsion has been carried out. Te...

CFD and FEM Model of an Underwater Vehicle Propeller

Publié en ligne: 28 oct. 2014

Pages: 40 - 45

DOI: https://doi.org/10.2478/pomr-2014-0028

Mots clés
ROV, ROV propeller, semi-open duct for horizontal propellers, rapid prototyping propeller

© 2014 Tadeusz Chruściel et. al.

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

CFD and FEM Model of an Underwater Vehicle Propeller

Publié en ligne: 28 oct. 2014

Pages: 40 - 45

DOI: https://doi.org/10.2478/pomr-2014-0028

Mots clésROV, ROV propeller, semi-open duct for horizontal propellers, rapid prototyping propeller

© 2014 Tadeusz Chruściel et. al.

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Mots clés
ROV, ROV propeller, semi-open duct for horizontal propellers, rapid prototyping propeller