<abstract xmlns="http://www.w3.org/1999/xhtml"><p>The analyses of the nonconformity of products are made in order to achieve the desired level of their quality. This is also the case in the analyzed enterprise located in south-eastern Poland. Due to production character in this enterprise to identify the incompatibilities of products the non-destructive tests are used. In the current approach to quality after identified the nonconformities the cause her arise were determined, it was noted in order to use by statistical analyzes. Unfortunately, no deeper qualitative analyzes were made which could specify the source of its creation. Therefore, it was considered that it is necessary to propose to use (near current actions according to non-destructive tests) the sequence of quality management instruments. In order to improve the quality control actions, the sequence of techniques which complement each other, i.e. non-destructive tests, Ishikawa diagram and 5Why method, was proposed. To demonstrate the effectiveness of the proposed sequence, the rear cover of the bearing turbine was selected as the subject of the analysis. The choice was conditioned by the unit character of production, which till now was discouraged a detailed analysis of sources of nonconformities. After analyzed the product with used the fluorescent method the nonconformities were identified on the rear cover of the bearing turbine, which was the porosity cluster. In order to identify the causes these nonconformities the Ishikawa diagram was drawn up. Next, the selected main causes (i.e. supplier of the product and nonconformities created during the production of the product) were analyzed the 5Why method in order to identify the source cause of the problem. In this case, it was the nonconformity material from the supplier. The proposed sequence, which uses the minimal resources let to show the wide range of information, which should be used to the improvement of quality. The presented the set of activities can be practised in each of the enterprises to analyze quality problems in order to identify the nonconformities and their causes.</p></abstract>

The analyses of the nonconformity of products are made in order to achieve the desired level of their quality. This is also the case in the analyzed enterprise located in south-eastern Poland. Due to production character in this enterprise to identify the incompatibilities of products the non-destructive tests are used. In the current approach to quality after identified the nonconformities the cause her arise were determined, it was noted in order to use by statistical analyzes. Unfortunately, no deeper qualitative analyzes were made which could specify the source of its creation. Therefore, it was considered that it is necessary to propose to use (near current actions according to non-destructive tests) the sequence of quality management instruments. In order to improve the quality control actions, the sequence of techniques which complement each other, i.e. non-destructive tests, Ishikawa diagram and 5Why method, was proposed. To demonstrate the effectiveness of the proposed sequence, the rear cover of the bearing turbine was selected as the subject of the analysis. The choice was conditioned by the unit character of production, which till now was discouraged a detailed analysis of sources of nonconformities. After analyzed the product with used the fluorescent method the nonconformities were identified on the rear cover of the bearing turbine, which was the porosity cluster. In order to identify the causes these nonconformities the Ishikawa diagram was drawn up. Next, the selected main causes (i.e. supplier of the product and nonconformities created during the production of the product) were analyzed the 5Why method in order to identify the source cause of the problem. In this case, it was the nonconformity material from the supplier. The proposed sequence, which uses the minimal resources let to show the wide range of information, which should be used to the improvement of quality. The presented the set of activities can be practised in each of the enterprises to analyze quality problems in order to identify the nonconformities and their causes.

An Improvement of Quality of the Rear Cover of Bearing Turbine with the use of Selected Methods

Conference Quality Production Improvement – CQPI

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

The analyses of the nonconformity of products are made in order to achieve the desired level of their quality. This is also the case in the analyzed enterprise...

An Improvement of Quality of the Rear Cover of Bearing Turbine with the use of Selected Methods

Publié en ligne: 08 oct. 2019

Pages: 456 - 463

Reçu: 04 mai 2019

Accepté: 22 mai 2019

DOI: https://doi.org/10.2478/cqpi-2019-0062

Mots clés
quality, improvement instruments, nonconformity, mechanical engineering

© 2019 Andrzej Pacana et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

An Improvement of Quality of the Rear Cover of Bearing Turbine with the use of Selected Methods

Publié en ligne: 08 oct. 2019

Pages: 456 - 463

Reçu: 04 mai 2019

Accepté: 22 mai 2019

DOI: https://doi.org/10.2478/cqpi-2019-0062

Mots clésquality, improvement instruments, nonconformity, mechanical engineering

© 2019 Andrzej Pacana et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Mots clés
quality, improvement instruments, nonconformity, mechanical engineering