<abstract xmlns="http://www.w3.org/1999/xhtml"> Dynamic mechanic (DMA) tests were performed to compare the mechanical behaviour of glass fibre reinforced epoxy laminate composites with SiO2 nanoparticle reinforced matrix. The selection of the most promising nanoparticle concentrations was considered in terms of elastic modulus and glass transition temperature. The reference specimens (0% nanoparticles) did not contain diluent accordingly the results do not allow the exact comparison with unreinforced composite, nevertheless the ranking of the nanocomposites was made. In terms of stiffness requirements 20% nanoparticles composites offer the best behaviour, 25% higher elastic modulus than 5% nanoparticles. For nano composites the glass transition temperature TG is the highest: 80°C, 77°C for 3%, 5% nanoparticles respectively and the lowest 75°C, 72°C , 71°C for 15%, 10% and 20% nanoparticles is respectively .</abstract>

Gdańsk University of Technology, Mechanical Faculty, 80-233 Gdańsk Narutowicza 11/12 Gdańsk, Poland

Aarhus University, Department of Engineering, 8200 Aarhus C, Dalgas Avenue 2, Denmark

DYNAMIC MECHANICAL BEHAVIOUR OF GFRP COMPOSITES WITH SiO2 NANO PARTICLES REINFORCED EPOXY MATRIX

<abstract xmlns="http://www.w3.org/1999/xhtml"> The purpose of the present paper is to demonstrate how a thermodynamic method can be used for solving a problem of the decarburisation of bainite laths and carbon diffusion distances in the matrix of ADI. This should in principle enable to examine the partitioning of carbon from supersaturated ferrite laths into adjacent austenite and the carbon content in retained austenite using analytical method. The paper presents an investigation of the time required for the diffusion of carbon out of supersaturated laths of ferrite into the retained austenite. A consequence of the precipitation of cementite from austenite during austempering is that the growth of bainitic ferrite can continue to larger extent and that the resulting microstructure is not an ausferrite but it is a mixture of bainitic ferrite, retained austenite and carbides. In case of this microstructure the product of austempering reaction in ductile iron is rather bainite than “ausferrite”.</abstract>

AUSFERRITIC OR BAINITIC TRANSFORMATION IN ADI

<abstract xmlns="http://www.w3.org/1999/xhtml"> This study presents the test results of Ti-20Nb-15Al alloy isothermal oxidation in air at 700°C with the consideration of the effect of annealing time on the condition of the surface layer. It was determined that, depending on the heating time, the surface of the tested alloy was characterized by a different colouring. This phenomenon was observed only at 700°C.</abstract>

THE ANALYSIS OF THE EFFECT OF TIME AND TEMPERATURE OF AIR ON THE COLOURING OF THE SURFACE LAYER OF O-Ti2AlNb BASED TITANIUM ALLOY

<abstract xmlns="http://www.w3.org/1999/xhtml"> The R6 procedure is one of the most advanced, innovative and effective method developed and recommended for use in problems of material behaviour and structural integrity of engineering structures with defects. The idea and basic assumptions of R6 procedure are described in the paper as well as example of its practical application in analysis of damaged bridge structural element. As a result of the research, the highly conservative approach of R6 procedure was observed, which estimated the level of hazardous loads as the elastic limit load for analysed element.</abstract>

ASSESSMENT OF MATERIAL BEHAVIOUR AND STRUCTURAL INTEGRITY OF ENGINEERING STRUCTURES BASED ON R6 PROCEDURE

AHEAD OF PRINT

Volume 24 (2024): Issue 1 (March 2024)

Volume 23 (2023): Issue 4 (December 2023)

Volume 23 (2023): Issue 3 (September 2023)

Volume 23 (2023): Issue 2 (June 2023)

Volume 23 (2023): Issue 1 (March 2023)

Volume 22 (2022): Issue 4 (December 2022)

Volume 22 (2022): Issue 3 (September 2022)

Volume 22 (2022): Issue 2 (June 2022)

Volume 22 (2022): Issue 1 (March 2022)

Volume 21 (2021): Issue 4 (December 2021)

Volume 21 (2021): Issue 3 (September 2021)

Volume 21 (2021): Issue 2 (June 2021)

Volume 21 (2021): Issue 1 (March 2021)

Volume 20 (2020): Issue 4 (December 2020)

Volume 20 (2020): Issue 3 (September 2020)

Volume 20 (2020): Issue 2 (June 2020)

Volume 20 (2020): Issue 1 (March 2020)

Volume 19 (2019): Issue 4 (December 2019)

Volume 19 (2019): Issue 3 (September 2019)

Volume 19 (2019): Issue 2 (June 2019)

Volume 19 (2019): Issue 1 (March 2019)

Volume 18 (2018): Issue 4 (December 2018)

Volume 18 (2018): Issue 3 (September 2018)

Volume 18 (2018): Issue 2 (June 2018)

Volume 18 (2018): Issue 1 (March 2018)

Volume 17 (2017): Issue 4 (December 2017)

Volume 17 (2017): Issue 3 (September 2017)

Volume 17 (2017): Issue 2 (June 2017)

Volume 17 (2017): Issue 1 (March 2017)

Volume 16 (2016): Issue 4 (December 2016)

Volume 16 (2016): Issue 3 (September 2016)

Volume 16 (2016): Issue 2 (June 2016)

Volume 16 (2016): Issue 1 (March 2016)

Volume 15 (2015): Issue 4 (December 2015)

Volume 15 (2015): Issue 3 (September 2015)

Volume 15 (2015): Issue 2 (June 2015)

Volume 15 (2015): Issue 1 (March 2015)

Volume 14 (2014): Issue 4 (December 2014)

Volume 14 (2014): Issue 3 (September 2014)

Volume 14 (2014): Issue 2 (June 2014)

Volume 14 (2014): Issue 1 (March 2014)

Volume 13 (2013): Issue 4 (December 2013)

Volume 13 (2013): Issue 3 (September 2013)

Volume 13 (2013): Issue 2 (June 2013)

Volume 13 (2013): Issue 1 (March 2013)

Volume 12 (2013): Issue 4 (January 2013)

Volume 12 (2012): Issue 3 (October 2012)

Volume 12 (2012): Issue 2 (June 2012)

Volume 12 (2012): Issue 1 (March 2012)

Volume 11 (2011): Issue 4 (December 2011)

Volume 11 (2011): Issue 3 (September 2011)

Volume 11 (2011): Issue 2 (June 2011)

Volume 11 (2011): Issue 1 (March 2011)

Volume 10 (2010): Issue 4 (December 2010)

Volume 10 (2010): Issue 3 (September 2010)

Volume 10 (2010): Issue 2 (June 2010)

Volume 10 (2010): Issue 1 (March 2010)

Volume 9 (2009): Issue 4 (December 2009)

Volume 9 (2009): Issue 3 (September 2009)

Volume 9 (2009): Issue 2 (June 2009)

Volume 9 (2009): Issue 1 (March 2009)

Volume 8 (2008): Issue 4 (December 2008)

Volume 8 (2008): Issue 3 (September 2008)

Volume 8 (2008): Issue 2 (June 2008)

Volume 8 (2008): Issue 1 (March 2008)

Advances in Materials Science

The journal is primarily focused on structure-properties relationship of engineering materials. Research articles addressing the following issues can be published as unique contributions across a variety of topics, including, but not limited to:   Structural and functional materials (metals and alloys, ceramics, polymers, composites)  Nanomaterials  Biomaterials  Materials for electronics  Materials for marine industry  Materials for energy industry  Materials for buildings  Surfaces, interfaces and thin films  Design, synthesis, processing and characterization techniques  Manufacturing of materials  Mechanics of materials  Stress analysis  Modeling of properties of materials  Methodology of testing the structure and properties of materials   The journal publishes original research articles and review articles. The possibility of publishing review articles should be agreed with the editors of the journal prior to submission.   Why subscribe and read   Internationally recognized source of up-to-date materials science information showing the newest achievements in area of structural and functional materials.  Why submit   A quick, reliable and constructive review  Short publication time  High quality electronic publication technologies  Open access   Rejection Rate   53%  Archiving  Sciendo archives the contents of this journal in Portico - digital long-term preservation service of scholarly books, journals and collections.  Plagiarism Policy  The editorial board is participating in a growing community of Similarity Check System's users in order to ensure that the content published is original and trustworthy. Similarity Check is a medium that allows for comprehensive manuscripts screening, aimed to eliminate plagiarism and provide a high standard and quality peer-review process. 

Advances in Materials Science

Volume 13 (2013): Issue 4 (December 2013)

DYNAMIC MECHANICAL BEHAVIOUR OF GFRP COMPOSITES WITH SiO₂ NANO PARTICLES REINFORCED EPOXY MATRIX

AUSFERRITIC OR BAINITIC TRANSFORMATION IN ADI

THE ANALYSIS OF THE EFFECT OF TIME AND TEMPERATURE OF AIR ON THE COLOURING OF THE SURFACE LAYER OF O-Ti2AlNb BASED TITANIUM ALLOY

ASSESSMENT OF MATERIAL BEHAVIOUR AND STRUCTURAL INTEGRITY OF ENGINEERING STRUCTURES BASED ON R6 PROCEDURE

Buscar

Todos los volúmenes y ediciones en esta revista