Iniciar sesión
Registrarse
Restablecer contraseña
Publicar y Distribuir
Soluciones de Publicación
Soluciones de Distribución
Temas
Arquitectura y diseño
Artes
Ciencias Sociales
Ciencias de la Información y Bibliotecas, Estudios del Libro
Ciencias de la vida
Ciencias de los materiales
Deporte y tiempo libre
Estudios clásicos y del Cercano Oriente antiguo
Estudios culturales
Estudios judíos
Farmacia
Filosofía
Física
Geociencias
Historia
Informática
Ingeniería
Interés general
Ley
Lingüística y semiótica
Literatura
Matemáticas
Medicina
Música
Negocios y Economía
Química
Química industrial
Teología y religión
Publicaciones
Revistas
Libros
Actas
Editoriales
Blog
Contacto
Buscar
EUR
USD
GBP
Español
English
Deutsch
Polski
Español
Français
Italiano
Carrito
Home
Revistas
Studia Geotechnica et Mechanica
Volumen 41 (2019): Edición 3 (September 2019)
Acceso abierto
Effect of settlement of foundations on the failure risk of the bottom of cylindrical steel vertical tanks for liquids
Eugeniusz Hotala
Eugeniusz Hotala
y
Rajmund Ignatowicz
Rajmund Ignatowicz
| 30 sept 2019
Studia Geotechnica et Mechanica
Volumen 41 (2019): Edición 3 (September 2019)
Acerca de este artículo
Artículo anterior
Artículo siguiente
Resumen
Artículo
Figuras y tablas
Referencias
Autores
Artículos en este número
Vista previa
PDF
Cite
Compartir
Article Category:
Research Article
Publicado en línea:
30 sept 2019
Páginas:
171 - 176
Recibido:
27 feb 2019
Aceptado:
05 jun 2019
DOI:
https://doi.org/10.2478/sgem-2019-0017
Palabras clave
Steel tank
,
soil settlement
,
tank deformations
,
plastic deformations
,
failure risk
© 2019 Eugeniusz Hotala, Rajmund Ignatowicz, published by Sciendo
This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 License.
Figure 1
Analyzed types of tank foundations: Type A, Type B, Type C.
Figure 2
Chosen cases of settlement of cylindrical tanks [3]: a) in the form of a trough, b) circumferential trough near or far from the shell, c) local trough near the shell
Figure 3
Penetration of rainwater under the bottom of tanks: Type A, Type B, Type C.
Figure 4
Geometry of the analyzed steel tank on a type A foundation and vertical deformations of the bottom plates uz and radial deformations of the cylinder shell ur.
Figure 5
Geometry of the analyzed steel tank on a type B foundation and vertical deformations of the bottom plates uz and radial deformations ur of the shell wall.
Figure 6
Geometry of the analyzed steel tank on a type C foundation with loosened soil zone (Kz1) and deformations uz of the bottom plate and ur of the shell.
Figure 7
Comparison of vertical deformations uz of tank bottom plates and radial deformations ur at the point No. 2 for type A and type B foundations of uniform stiffness Kz (Fig. 4, Fig. 5).
Figure 8
Elastic-plastic deformations ur of bottom plates at the point no. 2 for different values of width widths a, in which there was entire loosening of soil - foundation type B.
Figure 9
Elastic-plastic deformation of the bottom plate ur at point no. 1 with significant loosening of the soil at the width a = 350 mm- foundation type C.
Figure 10
Elastic-plastic deformation of bottom plates ur at point no. 2, when settling in the form of a trough (fig. 2a) – foundation type B.