<abstract xmlns="http://www.w3.org/1999/xhtml">Introduction: The total convergence of the axial walls is the angle made between the opposing axial walls of an abutment. The lower the taper value, the better the retention of the crowns is. Obtaining a proper convergence of the axial wall is a challenge for dental practitioners due to limited access and low visibility, but it also greatly depends on the clinician’s practical skills.This study aims to compare the total convergence of axial walls obtained after tooth preparation done by different experience practitioners in various positions of the patient and different working time (different days of the week, various parts of the day).Materials and methods: To perform this study, 40 acrylate model teeth have been prepared by two last year dental students and two prosthetists. All of them performed two teeth preparations per day in every working day of a week. All the prepared teeth have been photographed, and digitally measured.Results: The extremely statistically significant difference was found in the two beginners’ case, the values of the second beginner being much higher, as in the two experienced operators, where the values are higher for the second prosthetist.Conclusion: The total convergence of the axial wall did not depend on the operators’ experience or education level.</abstract>

Introduction: The total convergence of the axial walls is the angle made between the opposing axial walls of an abutment. The lower the taper value, the better the retention of the crowns is. Obtaining a proper convergence of the axial wall is a challenge for dental practitioners due to limited access and low visibility, but it also greatly depends on the clinician’s practical skills.This study aims to compare the total convergence of axial walls obtained after tooth preparation done by different experience practitioners in various positions of the patient and different working time (different days of the week, various parts of the day).Materials and methods: To perform this study, 40 acrylate model teeth have been prepared by two last year dental students and two prosthetists. All of them performed two teeth preparations per day in every working day of a week. All the prepared teeth have been photographed, and digitally measured.Results: The extremely statistically significant difference was found in the two beginners’ case, the values of the second beginner being much higher, as in the two experienced operators, where the values are higher for the second prosthetist.Conclusion: The total convergence of the axial wall did not depend on the operators’ experience or education level.

In vitro study about the abutment axial wall’s convergence

George Emil Palade University of Medicine, Pharmacy, Science, and Technology of Targu-Mures

Acta Stomatologica Marisiensis Journal

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

{"article-title":"In vitro study about the abutment axial wall\u2019s convergence"}

Introduction: The total convergence of the axial walls is the angle made between the opposing axial walls of an abutment. The lower the taper value, the better...

In vitro study about the abutment axial wall’s convergence

Publicado en línea: 10 ago 2020

Páginas: 269 - 274

Recibido: 06 jul 2020

Aceptado: 28 jul 2020

DOI: https://doi.org/10.2478/asmj-2020-0004

Palabras clave
convergence, taper, tooth preparation

© 2020 Diana Cerghizan et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

In vitro study about the abutment axial wall’s convergence

Publicado en línea: 10 ago 2020

Páginas: 269 - 274

Recibido: 06 jul 2020

Aceptado: 28 jul 2020

DOI: https://doi.org/10.2478/asmj-2020-0004

Palabras claveconvergence, taper, tooth preparation

© 2020 Diana Cerghizan et al., published by Sciendo

This work is licensed under the Creative Commons Attribution-NonCommercial-NoDerivatives 3.0 License.

Palabras clave
convergence, taper, tooth preparation