Determination of In-Plane Shear Properties of Laminate with V-Notch Rail Shear Test and Digital Image Correlation

Open access

Abstract

This article presents the results of the application of Digital Image Correlation (DIC) to measurements of in-plane shear modulus and strength of three different carbon fiber reinforced laminates. Three different approaches to shear strain calculations via DIC are evaluated and compared with standard strain gage measurements. Calculation of shear strain based on averaging DIC strain values of strain gages area in most cases yielded results closest to strain gages, while measurements based on single point strain measuring differed the most from strain gages. These results are attributed to shear strain distribution in the center area of the specimen. Thermoplastic matrix fabric reinforced composite had the lowest shear strength at 5% of shear strain, but the highest ultimate shear strength and strain at failure. Of thermosetting materials, laminate reinforced with unidirectional carbon fiber had shear modulus about 10% lower, than fabric reinforced laminate, but higher ultimate strength and strain at failure. This behavior is attributed to the presence of weaves in fabric reinforcing the laminate, causing shear stiffening of the material, but lowering its ability to deform under shear loading.

If the inline PDF is not rendering correctly, you can download the PDF file here.

  • [1] Kowalczyk P. “On applications of optical full-field strain measurements in validation and examination procedures” Transactions of the Institute of Aviation No. 4(245) 2016 46-51 DOI: 10.5604/05096669.1226354

  • [2] Bajurko P. Dobrzański P. 2018 “Experimental verification of numerical calculations with the use of digital image correlation” Transactions of the Institute of Aviation No. 2(251) 7-21

  • [3] F. Lagattu. J. Brillaud M.-C. Lafarie-Frenot “High strain gradient measurements by using digital image correlation technique” Materials Characterization 53 2004 17-28 DOI: 10.1016/j. matchar.2004.07.009

  • [4] Malesa M. et al. “Hybrid GI-DIC measurement procedure for hierarchical assessment of strain fields” Measurement Vol. 134 2019 83-88 DOI: 10.1016/j.measurement.2018.10.078

  • [5] Kowalczyk P. 2019 “Identification of mechanical parameters of composites in tensile tests using mixed numerical-experimental method” Measurement Vol. 135 2019 131-137 DOI: 10.1016/j.measurement.2018.11.027

  • [6] He Y. Makeev A. Shonkwiler B. “Characterization of nonlinear shear properties for composite materials using digital image correlation and finite element analysis” Composites Science and Technology 73 2012 64-71 DOI: 10.1016/j.compscitech.2012.09.010

  • [7] Kalariya Y. et al. “Applications of digital image correlation technique in composite research” (conference paper 9th International Symposium on Advanced Science and Technology in Experimental Mechanics New Delhi India 1-6 November 2014) DOI: 10.13140/2.1.5074.1442

  • [8] Perie J. N. et al. “Digital Image Correlation and biaxial test on composite material for anisotropic damage law identification” Int. Journal of Solids and Structures 46 2009 2388-2396 DOI: 10.1016/j.ijsolstr.2009.01.025

  • [9] Acciaioli A. et al. “Experimentally achievable accuracy using a digital image correlation technique in measuring small-magnitude (<0.1%) homogeneous strain fields” Materials 11 2018 751 DOI: 10.3390/ma11050751

  • [10] Hufenbach W. et al. “Analysing and modelling the 3D shear damage behavior of hybrid yarn textile-reinforced thermoplastic composites” Composite Structures 94 2011 121-131 DOI: 10.1016/j.compstruct.2011.07.010

  • [11] Olsson R. “A survey of test methods for multiaxial and out-of-plane strength of composite laminates” Composites Science and Technology 71 2011 773-783 DOI: 10.1016/j.compscitech.2011.01.022

  • [12] Cognard J.Y Sohier L. Davies P. “A modified Arcan test to analyze the behavior of composites and their assemblies under out-of-plane loadings” Composites: Part A 42 2011 111-121 DOI: 10.1016/j.compositesa.2010.10.012

  • [13] Gude M. et al. “Modified V-notched rail shear test fixture for shear characterization of textile-reinforced composite materials” Polymer Testing 43 2015 147-153 DOI: 10.1016/j.polymer-testing.2015.03.007

  • [14] Adams D. “Shear testing of high-shear strength composite laminates” Composites World vol. 4 No.7 2018 10-11

  • [15] Almeida J.H.S. et al. “Effect of fiber orientation on the shear behavior of glass fiber/epoxy composites” Materials and Design 65 2015 789-795 DOI: 10.1016/j.matdes.2014.10.003

  • [16] Totry E. et al. “Effect of fiber matrix and interface properties on the in-plane shear deformation of carbon-fiber reinforced composites” Composites Science and Technology 70 2010 970-980 DOI: 10.1016/j.compscitech.2010.02.014

  • [17] Stanley W. F. Mallon P.J. “Intraply shear characterization of a fibre reinforced thermoplastic composite” Composites: Part A 37 2006 939-948 DOI: 10.1016/j.compositesa.2005.03.017

  • [18] Standard test method for shear properties of composite materials by V-notched rail shear method ASTM D7078/D7078M-12 (West Conshohocken PA: ASTM International approved July 15 2012). DOI: 10.1520/D7078_D7078M-12

  • [19] Standard test method for in-plane shear response of polymer matrix composite materials by tensile test of a ±45° laminate ASTM D3518/D3518M-13 (West Conshohocken PA: ASTM International approved August 1 2013). DOI: 10.1520/D3518_D3518M-13

Search
Journal information
Metrics
All Time Past Year Past 30 Days
Abstract Views 0 0 0
Full Text Views 27 27 27
PDF Downloads 25 25 25