In 21st century, it has been observed that Wire Cut Electrical Discharge Machining (WEDM) has evolved as one of the most important non-traditional machining process. The popularity and its success lies because of its uniqueness towards producing different components which are very difficult to machine like titanium, tungsten carbide, Inconel materials etc and provides a platform in producing intricate complex shape which in many cases become impossible to machine by traditional machining methods. Pure sintered titanium bears very high specific strength, abrasion and corrosion resistances and thus machining this type of materials by conventional techniques becomes very difficult though this material finds immense applications in bio-plant and aerospace components. In the present work, WEDM on pure sintered titanium is studied. The different input parameters of WEDM like, pulse on time, pulse off time, wire tension and wire feed have been varied to investigate the output response like MRR, Surface Roughness (Ra), Kerf Width and Over Cut. A response surface methodology (4 factors 3 level) design of experiment (DOE) has been applied in this context to examine the machining ability of pure sintered titanium and results are found to be satisfactory and verified by confirmatory test. The machining parameters like pulse on time, pulse off time, wire tension and wire feed shows immense effect on the output responses and present study provide an optimal conditions of these input parameters to get the best output responses through RSM
If the inline PDF is not rendering correctly, you can download the PDF file here.
 Kumar, A., Kumar, V., Kumar, J. “A review on the state of the art in wire electric discharge machining (WEDM) process”, International Journal of Mechanical Engineering Research and Development (IJMERD) 1 (1), pp. 23 – 39, 2011.
 Kumar, R., Singh, S. “Current research trends in Wire Electrical Discharge Machining: An overview”, International Journal on Emerging Technologies 3 (1), pp. 33 – 40, 2012.
 Chakraborty, S., Debnath, D., Mallick, A. R., Das P. K. “Mechanical and thermal properties of hot pressed ZrB2 system with TiB2”, International Journal of Refractory Metals and Hard Materials 46, pp. 35 – 42, 2014.
 Jalaly, M., Bafghi, M. Sh., Tamizifar, M., Gotor F. J. “Formation mechanism of ZrB2 - Al2O3nano-composite powder by mechanically induced self-sustaining reaction” J. Mater Science 48, pp. 7557 – 7567, 2013.
 Selvakumar, G., Sornalatha, G., Sarkar, S., Mitra, S. “Experimental investigation and multi-objective optimization of wire electrical discharge machining (WEDM) of 5083 aluminium alloy”, Trans. Nonferrous Met. Soc. China 24, pp. 373 – 379, 2013.
 Garg, Sanjeev, K. R., Alakesh, M., Ajai, J. “Multi-objective optimization of machining characteristics during wire electrical discharge machining of Al / ZrO2 particulate reinforced metal matrix composite”, Journal of Engineering Research 1 (3), pp. 145 – 160, 2013.
 Khan, N. Z, Wahid, M., Singh, S., Siddiquee, A. N., Khan Z. A. “A study on micro hardness in wire electrical discharge machining based on Taguchi method”, International Journal of Mechanical and Production Engineering 1 (1), pp. 10 – 15, 2013.
 Goswami, A., Kumar, J. “An investigation into the machining characteristics of Nimonic 80A using CNC Wire - EDM”, International Journal of Advanced Engineering Technology III (1), pp. 170 – 174, 2012.
 Parashar, V., Rehman, A., Bhagoria, J. L., Puri, Y. M. “Kerfs width analysis for wire cut electro discharge machining of SS 304L using design of experiments”, Indian Journal of Science and Technology 3 (4), pp. 369 – 373, 2010.
 Datta, S., Sankar Mahapatra, S. “Modelling, simulation and parametric optimization of wire EDM process using response surface methodology coupled with grey-Taguchi technique”, International Journal of Engineering, Science and Technology 2 (5), pp. 162 – 183, 2010.
 Rutvik A. Shah, Darji, A. “A literature review on effect of machining parameters in Wire-EDM”, IJSRD - International Journal for Scientific Research & Development, 1 (9), pp. 1840 – 1842, 2013.
 Kumar, A., Kumar, V. Kumar, J. “Prediction of surface roughness in wire electric discharge machining (WEDM) process based on Response Surface Methodology” International Journal of Engineering and Technology 2 (4), pp. 708 – 719, 2012.
 Singh, A. K., Kumar, S., Singh, V. P. “Electrical discharge machining of super alloys: A Review”, IJRMET - International Journal of Research in Mechanical Engineering & Technology 3 (2), pp. 157 – 161, 2013.
 Prajapati, S. B., Patel, N.S. “Effect of process parameters on performance measures of wire - EDM for AISI AS tool steel”, International Journal of Computational Engineering Research 03 (4), pp. 274 – 278, 2013.
 Geetha, Bezawada Sreenivasulu, M., Harinath Gowd, G. “Modelling & Analysis of performance characteristics of wire EDM of SS304” IJITEE - International Journal of Innovative Technology and Exploring Engineering 3 (4), pp. 122 – 125, 2013.
 Subrahmanyam, S. V. Sarcar, M. M. M. “Evaluation of optimal parameters for machining with wire cut EDM using Greay-Taguchi method”, International Journal of Scientific and Research Publications 3 (3), pp. 1 – 9, 2013.
 Shah, R. A., Darji, A. “A Review: An experimental effect of electrode material on MRR, kerf width and surface roughness of AISI D2 tool steel in WEDM”, Indian Journal of Applied Research 3 (12), pp. 211 – 213, 2013.
 Abbas, N. M., Solomon, D. G., Md. Bahari, F. ” A review on current research trends in electrical discharge machining (EDM)”, International Journal of Machine Tools and Manufacture 47 (7 – 8), pp. 1214 – 1228, 2007.
 Ho, K. H., Newman, S.T., Rahimifard, S., Allen, R. D. “State of the art in wire electrical discharge machining (WEDM)” (2004), International Journal of Machine Tools and Manufacture 44 (12 – 13), pp. 1247 – 1259, 2004.
 Yan, M.-T., Huang, P.-H. “Accuracy improvement of wire-EDM by real-time wire tension control”, International Journal of Machine Tools and Manufacture 44 (7–8), pp. 807 – 814, 2004.
 Alias, A., Abdullah, B., Abbas, N. M. “Influence of Machine Feed Rate in WEDM of Titanium Ti-6Al-4V with Constant Current (6A) Using Brass Wire”, Procedia Engineering 41, pp. 1806 – 1811, 2012.
 Simao, J., Lee, H. G., Aspinwall, D.K., Dewes R.C., Aspinwall E.M. “Workpiece surface modification using electrical discharge machining”, International Journal of Machine Tools and Manufacture 43 (2), pp. 121 – 128, 2003.
 Gautier, G., Priarone, P. C., Rizzuti, S., Settineri, L., Tebaldo, V. “A Contribution on the Modelling of Wire Electrical Discharge Machining of a γ-TiAl Alloy”, Procedia CIRP 31, pp. 203 – 208, 2015. DOI: https://doi.org/10.1016/j.procir.2015.03.019
 Poletti, C., Balog, M., Schubert, T., Liedtke, V., Edtmaier, C. “Production of titanium matrix composites reinforced with SiC particles”, Composites Science and Technology 68, pp. 2171 – 2177, 2008.
 Madyira, D. M., Akinlabi, E. T. “Effects of Wire Electrical Discharge Machining on Fracture Toughness of Grade 5 Titanium Alloy”, Proceedings of the World Congress on Engineering II, 2014.
 Himanshu, P. R., Lalta, P., Mayank, P., Vineet, T. “An Estimating The Effect Of Process Parameters On Metal Removal Rate And Surface Roughness In WEDM Of Composite AL6063/SIC/AL2O3 By Taguchi Method”, Journal of Mechanical Engineering – Strojnícky časopis 67 (2), pp. 25 – 36, 2017. DOI: 10.1515/scjme-2017-0015.
 Moi, S. Ch., Pal P. K., Bandyopadhyay, A., Rudrapati, R. “Determination Of Tungsten Inert Gas Welding Input Parameters To Attain Maximum Tensile Strength Of 316L Austenitic Stainless Steel”, Journal of Mechanical Engineering – Strojnícky časopis 68 (3), pp. 231 – 248, 2018. DOI: 10.2478/scjme-2018-0037.
 Srinivasa Rao, M., Ramanaiah, N. “Optimization Of Process Parameters For FSW Of Al-Mg-Mn-Sc-Zr Alloy Using CCD And RSM”, Journal of Mechanical Engineering – Strojnícky časopis, 68 (3), pp. 195 – 224, 2018. DOI: 10.2478/scjme-2018-0035