Significance of Fines in Hot Mix Asphalt Synthesis

Open access

Abstract

According to their size, aggregates are classified in coarse grained, fine grained, and fines. The determination of fines content in aggregate materials is very simple and is performed through the aggregate washing during the sieving procedure to define the gradation curve. The very fine material consists of grains having a size lower than 63 μm. The presence of fines directly influences the composition and performance of concrete and asphalt mixtures (e.g. asphalt content, elasticity, fracture). The strength and load carrying capacity of hot mix asphalt (HMA) results from the aggregate framework created through particle-particle contact and interlock. Fines or mineral filler have a role in HMA. The coarse aggregate framework is filled by the sand-sized material and finally by the mineral filler. At some point, the smallest particles lose contact becoming suspended in the binder not having the particle-particle contact that is created by the larger particles. The overall effect of mineral filler in hot mix asphalt specimens has been investigated through a series of laboratory tests. It is clear that a behaviour influenced by the adherence of fines to asphalt film has been developed. The optimum bitumen content requirement in case of stone filler is almost the same as that for fly ash. It has been found that the percentage of fly ash filler is crucial if it exceeds approximately a value of 4%.

If the inline PDF is not rendering correctly, you can download the PDF file here.

  • [1]. ZULKATI W. DIEW D. DELAI: D. “Effects of fillers on properties of asphalt concrete mixture” Journal of Transportation Engineering vol. 138 No. 7 pp. 902–910 2012.

  • [2]. B.M. HARRIS K.D. STEWART: “Analysis of mineral fillers and mastics used in stone matrix asphalt” Journal of the Association of Asphalt Paving Technologists vol. 6 pp. 54–95 1995.

  • [3]. S. WU J. ZHU J. ZHONG D. WANG: “Experimental investigation on related properties of asphalt mastic containing recycled brick powder” Construction Building Materials vol. 25 No. 6 pp. 2883–2887 2011.

  • [4]. M. RATNASAMY A. ELTAHER: “The effect of type and particle size of industrial wastes filler on indirect tensile stiffness and fatigue performance of Stone Mastic Asphalt mixtures” Australian Journal of Basic and Applied Sciences vol. 5 No. 11 pp. 297–308 2011.

  • [5]. I. ISHAI J. CRAUS: “Effects of some aggregate and filler characteristics on behavior and durability of asphalt paving mixtures” Transportation Research Record 1530 Transportation Research Board National Research Council Washington DC pp. 75–85 1996.

  • [6]. P. KUMAR H.C. MEHNDIRATTA V. SINGH: “Use of fly ash in bituminous layer of pavement” Indian Highways pp. 41–50 2008.

  • [7]. V. SHARMA S. CHANDRA R. CHOUDHARY: “Characterization of fly ash bituminous concrete mixes” Journal of Materials in Civil Engineering vol. 22 No. 12 pp. 1209-1216 2010.

  • [8]. A.H. ALJASSAR S. METWALI M.A. ALI: “Effect of filler types on Marshall Stability and retained strength of asphalt concrete”. The International Journal of Pavement Engineering vol. 5 No. 1 pp. 47–51 2004.

  • [9]. H. AL-SAFFAR: “The effect of filler type and content on hot asphalt concrete mixtures properties” Al-Rafidain Engineering vol. 21 No. 6 pp. 88-100 2013.

  • [10]. T. RAVINDRA R.K. JAIN M.H. KOSTHA: “Effect of fillers on bituminous paving mixes” International Journal of Engineering Research & Science & Technology vol. 2 No. 4 pp. 137-142 2013.

  • [11]. H.S. DO P.H. MUN R. SUK: “A study on engineering characteristics of asphalt concrete using filler with recycled waste lime” Waste Management vol. 28 pp. 191–199 2008.

  • [12]. J.C. PETERSON: “Lime-treated pavements offer increased durability” Roads and Bridges Journal vol. 26 No. 1 pp. 85–87 1988.

  • [13]. L. DARTNELL: “A study of limestone dust calcined shale and asbestos as mineral fillers in asphalt paving mixtures” Canadian Tech. Asphalt Assoc. Proceedings vol. 12 pp. 51–60 1967.

  • [14]. B. FUCIC: “Influence of filler types on the properties of bituminous mixtures” Research Report Zagreb University Zagreb 137 p. 1976.

  • [15]. S.D. RAMSWAMY M.A. AZIZ: “Assessment of effect of filler on the stripping of bituminous mix”. 4th Conference of the Road Engineering Association of Asia and Australasia Jakarta Indonesia vol. 3 pp. 159–170 1983.

  • [16]. J.C. ROSNER R.D. PAVLOUICH J.G. CHEHOVITS: “Fly ash as a mineral filler and anti-strip agent for asphalt concrete” Report No. FHWA-AZ-81/173 Washington DC FHWA 1981.

  • [17]. M.G. BAIG H.I. AL-ABDUL WAHAB: “Mechanistic evaluation of lime modified asphalt concrete mixtures” ASCE Journal of Materials in Civil Engineering vol. 10 No. 3 pp. 153–160 1998.

  • [18]. M.N. RAHMAN M.A. SOBHAN: “Use of non-conventional fillers on asphalt-concrete mixture” International Journal of Innovation and Applied Studies vol. 3 No. 4: pp. 1101-1109 2013.

  • [19]. AMERICAN SOCIETY FOR TESTING AND MATERIALS: ASTM D 1559: “Test method for resistance to plastic flow of bituminous mixtures using Marshall Apparatus” Annual Book of ASTM Standards 2000 Sec. 4 — Construction Vol. 04.03 Road and Paving Materials; Vehicle – Pavement Systems West Conshohocken PA. ASTM International 2000.

Search
Journal information
Metrics
All Time Past Year Past 30 Days
Abstract Views 0 0 0
Full Text Views 380 184 9
PDF Downloads 180 109 6