Workpiece Temperature Variations During Flat Peripheral Grinding

Vitalii A. Smirnov 1  and Aleksandr V. Repko 1
  • 1 Votkinsk Branch of Kalashnikov Izhevsk State Technical University Department Technology of Mechanical Engineering and Instrument Making Studencheskaya 7, , Izhevsk , RUSSIA


The paper presents the results of researches of temperature variations during flat peripheral grinding. It is shown that the temperature variations of the workpiece can reach 25...30% of the average values, which can lead to some thermal defects. A nonlinear two-dimensional thermophysical grinding model is suggested. It takes into account local changes in the cutting conditions: the fluctuation of the cut layer and the cutting force, the thermal impact of the cutting grains, and the presence of surface cavities in the intermittent wheel. For the numerical solution of the problem, the method of finite differences is adapted. Researches of the method stability and convergence are made, taking into account the specific nature of the problem. A high accuracy of the approximation of the boundary conditions and the nonlinear heat equation is provided. An experimental verification of the proposed thermophysical model was carried out with the use of installation for simultaneous measurement of the grinding force and temperature. It is shown that the discrepancy between the theoretical and experimental values of the grinding temperature does not exceed 5%. The proposed thermophysical model makes it possible to predict with high accuracy the temperature variations during grinding by the wheel periphery.

If the inline PDF is not rendering correctly, you can download the PDF file here.

  • [1] Z. Ding, B. Li and S.Y. Liang. “Phase transformations and residual stress of Maraging C250 steel during grinding”, Materials Letters, vol. 154, pp. 37-39, Sep. 2015.

  • [2] V.F. Formalev and D.L. Reviznikov. Numerical methods. Moscow: FIZMATLIT, 2004.

  • [3] R.J. Gu, M. Shillor, G.C. Barber and T. Jen. “Thermal analysis of the grinding process”, Mathematical and Computer Modelling, vol. 39, pp. 991-1003, May 2004.

  • [4] J. Kulka, M. Mantic, G. Fedorko and V. Molnár. “Analysis of crane track degradation due to operation”, Engineering Failure Analysis, vol. 59, pp. 384-395, Jan. 2016.

  • [5] A. Lefebvre, P. Lipinski, P. Vieville and C. Lescalier. “Experimental analysis of temperature in grinding at the global and local scales”, Machining Science and Technology, vol. 12, no. 1, pp. 1-14, Mar. 2008.

  • [6] S. Malkin and C. Guo. “Thermal Analysis of Grinding”, CIRP Annals, vol. 56, no. 2, pp. 760-782, Nov. 2007.

  • [7] I.D. Marinescu, M. Hitchiner, E. Uhlmann, W.B. Rowe and I. Inasaki. Handbook of machining with grinding wheels. Boca Raton, FL: CRC Press Taylor & Francis Group, 2006.

  • [8] V.A. Nosenko and S.V. Nosenko. Metal grinding technology. Stariy Oskol: TNT, 2016.

  • [9] E. Pivarčiová and P. Božek. “Registration of holographic images based on integral transformation”, Computing and informatics, vol. 31, no. 6, pp. 1369-1383, 2012.

  • [10] N. Ortega, H. Bravo, I. Pombo, J.A. Sanchez and G. Vidal. “Thermal analysis of creep feed grinding”, Procedia Engineering, vol. 132, pp. 1061-1068, 2015.

  • [11] V.A. Smirnov. “The influence of geometric error of the grinding wheel and technological system vibrations on the chip thickness change by peripheral flat grinding”, Bulletin of ISTU, vol. 3, pp. 16-18, Mar. 2008.

  • [12] V. Sviatskii, A. Repko, D. Janačova, Z. Ivandič, O. Perminova and Y. Nikitin. “Regeneration of a fibrous sorbent based on a centrifugal process for environmental geology of oil and groundwater degradation”, Acta Montanistica Slovaca, vol. 21, no. 4, pp. 272-279, 2016.

  • [13] R. Grega, J. Krajnak, L. Zulova, G. Fedorko and V. Molnár. “Failure analysis of driveshaft of truck body caused by vibrations”, Engineering Failure Analysis, vol. 59, pp. 208-215, Sept. 2017.

  • [14] J. Černecký, K. Valentová, E. Pivarčiová and P. Božek. “Ionization Impact on the Air Cleaning Efficiency in the Interior”, Measurement Science Review, vol. 15, no. 4, pp. 156-166, 2015.


Journal + Issues