Experimental Study and Response Surface Methodology for Investigation of FSP Process

Open access

Abstract

The article presents the effect of rotational and travelling speed and down force on the spindle torque acting on the tool in Friction Stir Processing (FSP) process. The response surface methodology (RSM) was applied to find a dependence combining the spindle torque acting on the tool with the rotational speed, travelling speed and the down force. The linear and quadratic models with interaction between parameters were used. A better fitting was achieved for a quadratic model. The studies have shown that the increase in rotational speed causes a decrease in the torque while the increase in travelling speed and down force causes an increase in the torque. The tests were conducted on casting aluminium alloy AlSi9Mg. Metallography examination has revealed that the application of FSP process results in a decrease in the porosity in the modified material and microstructure refining in the stir zone. The segregation of Si and Fe elements was evident in the parent material, while in the friction stir processed area this distribution was significantly uniform.

[1] Ma Z.Y., Sharma S.R., Mishra R.S.: Microstructural Modification of As-Cast Al-Si-Mg Alloy by Friction Stir Processing. Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science 37 (2006) 3323-3336.

[2] Oh-Ishi K., McNelley T.R.: The Influence of Friction Stir Processing Parameters on Microstructure of As-Cast NiAl Bronze. Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science 36 (2005) 1575-1585.

[3] Weglowski M.St.: Technologia Friction Stir Processing - nowe mozliwosci. Biuletyn Instytutu Spawalnictwa 55 (2011) 25-31.

[4] Weglowski M.St., Dymek S.: Microstructural modification of cast aluminium alloy AlSi9Mg via Friction Modified Processing. Archives of Metallurgy and Materials 57 (2012) 71-78.

[5] Weglowski M.St., Pietras A.: Friction Stir Processing - analysis of the process. Archives of Metallurgy and Materials 56 (2011) 779-788.

[6] Schmidt H., Hattel J., Wert J.: An analytical model for the heat generation in friction stir welding. Modeling and Simulation in Materials Science and Engineering 12 (2004) 143-157.

[7] Weglowski M.St., Hamilton C., Dymek S.: A coupled thermal/material flow model of friction stir surfacing applied to AlMg9Si. Materials Engineering 34 (2013) 201-204.

[8] Cui G.R., Ma Z.Y., Li S.X.: Periodical plastic flow pattern in friction stir processed Al-Mg alloy. Scripta Materialia 58 (2008) 1082-1085.

[9] Kopuscianski M., Weglowski M.St., Pietras A., Weglowska A., Hamilton C., Dymek S.: Friction Stir processing as a fabricating route of dispersion strengthened aluminum alloys. Materials Engineering 34 (2013) 303-305.

[10] Paradiso V., Astarita A., Carrino L. et al.: Numerical optimization of selective superplastic forming of friction stir processed AZ31 Mg alloy. Key Engineering Materials 554-557 (2013) 2212-2220.

[11] Lakshminarayanan A.K., Balasubramanian V.: Comparison of RSM with ANN in predicting tensile strength of friction stir welded AA7039 aluminium alloy joints. Trans. Nonferrous Met. Soc. China 19 (2009) 9-18.

[12] Myers R.H., Montgomery D.C., Anderson-Cook Ch.M.: Response Surface Methodology. Process and product optimization using design experiments. New York, Wiley, 2009.

[13] Arora A., Nandan R., Reynolds A.P., DebRoy T.: Torque, power requirement and stir zone geometry in friction stir welding through modelling and experiments. Scripta Materialia 60 (2009) 13-16.

Archive of Mechanical Engineering

The Journal of Committee on Machine Building of Polish Academy of Sciences

Journal Information


CiteScore 2016: 0.44

SCImago Journal Rank (SJR) 2016: 0.162
Source Normalized Impact per Paper (SNIP) 2016: 0.459

Metrics

All Time Past Year Past 30 Days
Abstract Views 0 0 0
Full Text Views 226 184 14
PDF Downloads 120 106 7