Experimental Data in Vehicle Modeling

Open access

Abstract

This article is about a vehicle model which is created in software Matlab Simscape Driveline. In this model the motor is created like a subsystem by Simulink blocks and input data were measured by single roller dynamometer for cars (SRD). Measured data are the input into the model by Lookup Table block. The vehicle model is made by gear, differential, tire and vehicle body blocks. We studied the forces on tires, the vehicle velocity and the slip.

References

  • [1] Kohar, R. & Hrcek, S. (2014). Dynamic analysis of a rolling bearing cage with respect to the elastic properties of the cage for the axial and radial load cases. Communications, 16 (3A), 74-81. ISSN 1335-4205.

  • [2] Hrcek, S., Kohar, R. & Medvecky, S. (2012). Determination on the maximum roller bearing load with regards to durability thereof using FEM analysis. Communications, 14 (3), 55-61. ISSN 1335-4205.

  • [3] Drozdziel, P., Brumercikova, E. & Bukova, B. (2015). The Use of Progressive Methods of Serving Passengers. Transport problems, 10 (4). ISSN 1896-0596.

  • [4] Nieoczym, A. (2005). Application of a transportation flux for determining qualitative indices. Communications, 7 (1), 47-48. ISSN 1335-4205.

  • [5] Kucera, L., Lukac, M., Jurak, L. & Brumercik, F. (2009). Hydromechanical Automatic Transmission. Communications, 11 (2), 33-35. ISSN 1335-4205.

  • [6] Drozdziel, P. & Krzywonos, L. (2009). The Estimation of the Reliability of the First Daily Diesel Engine Start-up During its Operation in the Vehicle. Eksploatacja i Niezawodnosc – Maintenance and Reliability, 1 (41), 4-10. ISSN 1507-2711.

  • [7] Jedlinski, L., Caban, J., Krzywonos, L., Wierzbicki, S. & Brumercik, F. (2015). Application of vibration signal in the diagnosis of IC engine valve clearance. Journal of Vibroengineering, 17 (1), 175-187. ISSN 1392-8716.

  • [8] Lukac, M., Brumercik, F., Krzywonos, L. & Drozdziel, P. (2014). Tension mechanism dynamic analysis. Communications, 16 (3A), 184-188. ISSN 1335-4205.

  • [9] Filo, M. & Lukac, M. (2005). Modeling and Simulation of Mechanisms with Computer Support, Zilina: EDIS-publisher of University of Zilina, ISBN 80-8070-466-X.

  • [10] Caban, J., Drozdziel, P., Vrabel, J., Sarkan, B., Marczuk, A., Krzywonos, L. & Rybicka, I. (2016). The research on ageing of glycol-based brake fluids of vehicles in operation. Advances in Science and Technology, 10 (32), 9-16. ISSN 2299-8624.

  • [11] Caban, J., Marczuk, A., Sarkan, B. & Vrabel, J. (2015). Studies on operational wear of glycol-based brake fluid. Przemysł Chemiczny, 94 (10), 1802-1806. ISSN 0033-2496.

  • [12] Faturik, L., Trsko, L., Hrcek, S. & Bokuvka, O. (2014). Comparison of structural design in high and ultra-high cycle fatigue regions. Transactions of FAMENA, 38 (4), 1-12. ISSN 1333-1124.

  • [13] Marczuk, A., Caban, J., Savinykh, P., Turubanov, N. & Zyryanov, D. (2017). Maintenance research of a horizontal ribbon mixer. Eksploatacja i Niezawodnosc – Maintenance and Reliability, 19 (1), 121-125. ISSN 1507-2711.

  • [14] Walczak, M., Zwierzchowski, M., Bienias, J. & Caban, J. (2017). The tribological characteristics of Al-Si/graphite composite. Tribologia, 1, 97-104. ISSN 0208-7774.

Journal Information

Metrics

All Time Past Year Past 30 Days
Abstract Views 0 0 0
Full Text Views 35 35 29
PDF Downloads 7 7 5