Abstract
In this study, behaviour of bi-adhesive used in the repair of damaged parts was analyzed, using the finite element method. In a double-strap joint with an embedded patch, patch is embedded into the adherents for structural requirements. In addition, to increase the strength of the joint, two adhesives are used to bond the adherents. This approach reduces stress concentration at the overlap ends, increases the load capacity and delays the failure. These effects give rise to higher joint strength. For this purpose, a stiff adhesive, FM73 produced by Cytec Fiberite, was applied in the middle portion of the overlap, while a softer adhesive, SBT9244 from 3M, was applied towards the edges, prone to stress concentrations. Non-linear finite element analyses were carried out to predict the failure loads, to assist with the geometric design and to identify effective ratios of sizes to maximize joint strength.
References
[1] Sabrina, F., M. Riadh, Z. Xiao-Ling. Experimental and Finite Element Analysis of a Double Strap Joint between Steel Plates and Normal Modulus CFRP. Composite Structure, 75 (2006), 156-162.
[2] Lee, H. K., S. H. Pyo, B. R. Kim. On Joint Strengths, Peel Stresses and Failure Modes in Adhesively bonded Double-strap supported Single-lap GFRP Joints. Composite Structure, 8 (2009), 44-54.
[3] Peter, C., R. Francis. Stress Analysis of Double-strap Bonded Joints using a Variational Method. Int. J. Adhesion Adhesives, 21 (2001), 241-247.
[4] Campilho, R. D. S. G., M. F. S. F. de Moura, D. A. Ramantani, J. J. L. Morais, J. J. M. S. Domingues. Tensile Behaviour of Three-dimensional Carbon-epoxy Adhesively Bonded Single- and Double-strap Repairs. Int. J. Ad- hesion Adhesives, 29 (2009), 678-686.
[5] Jarry, E., R. A. Shenoi. Performance of Butt Strap Joints for Marine Applications. Int. J. Adhesion Adhesives, 26 (2006), 162-176.
[6] C¸ itil, S¸ , S. Temiz, H. Altun, A. Ozel. Determination of Mechanical Proper- ties of Double-strap Adhesive Joints with an Embedded Patch. Journal Adhesion Sci. Technol., 18 (2011), 2555-2567.
[7] Hart-Smith, L. J. Adhesive-bonded Single-lap Joints, NASA Technical Report CR-112236, TX, Houston, NASA, 1973.
[8] Adams, R. D., J. Comyn, W. C. Wake. Structural Adhesive Joints in Engineering, Amsterdam, Elsevier, 1997.
[9] Adams, R. D., J. A. Harris. The Influence of Local Geometry on the Strength of Adhesive Joints. Int. J. Adhesion Adhesives, 7 (1987), 69-80.
[10] Kinloch, A. J. Adhesion and Adhesives, London, Chapman and Hall, 1993.
[11] Al-Samhan, A., S. M. H. Darwish. Finite Element Modelling of Weldbonded Joints. Journal Mater. Proc. Technol., 142 (2003), 587-598.
[12] Tsai, M. Y., J. Morton. The effect of a Spew Fillet on Adhesive Stress Distributions in Laminated Composite Single-lap Joints. Composite Structures, 32 (1995), 123-131.
[13] Apalak, M. K., R. Davies. Analysis and Design of Adhesively Bonded Corner Joints: Fillet Effect. International Journal Adhesion Adhesives, 14 (1994), 163-174.
[14] Temiz, S. Application of Bi-adhesive in Double-strap Joints subjected to Bending Moment. Journal of Adhesion Sci. Technol., 20 (2006), 1547-1560.
[15] Pires, I., L. Quintino, J. F. Durodola, A. Beevers. Performance of Bi- adhesive Bonded Aluminium Lap Joints. Int. J. Adhesion Adhesives, 23 (2003), 215-223.
[16] Kumar, S., P. C. Pandey. Behaviour of Bi-adhesive Joints. Journal Adhesion Sci. Technol., 24 (2010), 1251-1281.
[17] da Silva, L. F. M., C. Q. M. J. Lopes. Joint Strength Optimization by the Mixed-adhesive Technique. Int. J. Adhesion Adhesives, 29 (2009), 509-514.
[18] das Neves, P. J. C., L. F. M. da Silva, R. D. Adams. Analysis of Mixed Adhesive Bonded Joints Part II: Parametric Study. Journal of Adhesion Sci. Technol., 23 (2009), 35-61.
[19] Marques, E. A. S., L. F. M. da Silva. Joint Strength Optimization of Adhesively Bonded Patch. Journal of Adhesion, 84 (2008), 915-934.
[20] Aydin , M. D., A. Ozel ,S. Temiz. Effect of Protrusionat the Ends of Bondline in Single Lap Joints under Tension and Bending. J. Adhesion Sci. Technol., 18 (2004), 1589-1602.
[21] ANSYS. The General Purpose Finite Element Software, TX, Houston, Swanson Analysis Systems, 2012.
[22] Adin, Hamit. The Investigation of the Effect of Angle on the Failure Load and Strength of Scarf Lap Joints. J. Applied Mathematical Modelling, 36 (2012), 2858.
[23] Adin, Hamit, D. M. Emin. Investigation of the Effect of Different Variables on Strength of Adhesive Joints. Mat.-wiss. U. Werkstofftech., 45 (2014), No. 10, 869-878.
[24] Özer, H., Öz Özkan. Three Dimensional Finite Element Analysis of Biadhesively Bonded Double Lap Joint. International Journal of Adhesion & Adhesives, 37 (2012), 50-55.
