Reduction of Deformations during Welding Metal Wire Mesh with Frames

Open access

Abstract

The article presents an issue referring to a reduction of deformation during welding metal wire mesh into the frames. A problem of a possible reduction of deformations was described taking into account characteristics of a construction of a welded element. Technological tests and their results are provided. Technological recommendations relating to the reduction of deformations of the welded element are given.

[1] Praca zbiorowa; Poradnik inżyniera - Spawalnictwo tom I i II, WNT, Warszawa 2005.

[2] B. Pierożek, J. Lassociński, Spawanie łukowe stali w osłonach gazowych. WNT, Warszawa 1987.

[3] R. Krawczyk, Zakresy parametrów spawania w zależności od przenoszenia metalu w łuku spawalniczym. Biuletyn Instytutu Spawalnictwa. Nr 4/2014.

[4] J. Słania, Plany spawania. Teoria i praktyka. Agenda wydawnicza SIMP, Redakcja Przegląd Spawalnictwa, Warszawa 2013.

[5] M. Myśliwiec, Cieplno-mechaniczne podstawy spawalnictwa. Warszawa, PWN 1972.

[6] T. Węgrzyn, J. Piwnik, B. Łazarz, D. Hadryś, Main micro-jet cooling gases for steel welding, Archives of Metallurgy and Materials, 58 (2), 555 - 557 (2013).

[7] T. Węgrzyn, J. Piwnik, D. Hadryś, Oxygen in steel WMD after welding with micro-jet cooling, Archives of Metallurgy and Materials, Vol. 58, issue 4, 2013: pp. 1067 - 1070.

[8] W. Tarasiuk, B. Szczucka - Lasota, J. Piwnik, W. Majewski, Tribological Properties of Super Field Weld with Micro-Jet Process, Adv. Mat. Res. 1036, 452-457 (2014).

[9] T. Węgrzyn, J. Piwnik, J. Wieszała, D. Hadryś, Control over the steel welding structure parameters by micro-jet cooling. Archives of Metallurgy and Materials, 57 (1), 679-685 (2012).

[10] T. Węgrzyn, The Classification of Metal Weld Deposits in Terms of the Amount of Oxygen. PROC OF ISOPE, IV,1999, 212 - 216.

[11] T. Węgrzyn, The Classification of Metal Weld Deposits in Terms of the Amount of Nitrogen. Procedings of ISOPE´2000, V, 2000, 130 - 134.

[12] B. Szczucka-Lasota, B. Formanek, A. Hernas, K. Szymański, Oxidation models of the growth of corrosion products on the intermetallic coatings strengthened by a fine dispersive Al2O3. Journal of Materials Processing Technology, volumes 164-165, 935 - 939 (2005).

[13] J. Słania, Influence of phase transformations in the temperature ranges of 1250-1000ºC and 650-350ºC on the ferrite content in austenitic welds made with T 23 12 LRM3 tubular electrode. Metallurgy and Materials, 3, 2010-2014 (2005).

[14] A. Lisiecki, Diode laser welding of high yield steel. Proc. of SPIE Vol. 8703, Laser Technology 2012: Applications of Lasers 87030S (January 22, 2013), DOI: 10.1117/12.2013429.

[15] A. Lisiecki, Welding of titanium alloy by Disk laser. Proc. of SPIE Vol. 8703, Laser Technology 2012: Applications of Lasers 87030T (January 22, 2013), DOI: 10.1117/12.2013431.

[16] G. Golański, P. Gawień, J. Słania, Examination of Coil Pipe Butt Joint Made of 7CrMoVTib10 - 10(T24) Steel After Service, Archives of Metallurgy and Materials, 57 (2), (2012).

[17] R. Burdzik, P. Folęga, B. Łazarz, Z. Stanik, J. Warczek, Analysis of the impact of surface layer parameters on wear intensity of friction pairs. Archives of Metallurgy and Materials, 57 (4), 987 - 993 (2012).

[18] B. Oleksiak, G. Siwiec, A. Blacha-Grzechnik, J. Wieczorek, The obtained of concentrates containing precious metals for pyrometallurgical processing, Metalurgija 53(4), 605-608 (2014).

[19] R. Burdzik, Ł. Konieczny, Research on structure, propagation and exposure to general vibration in passenger car for different damping parameters, Journal of Vibroengineering 15(4), 1680-1688 (2013).

[20] R. Burdzik, Research on the influence of engine rotational speed to the vibration penetration into the driver via feet - multidimensional analysis. Journal of Vibroengineering, 15 (4), 2114 - 2123 (2013).

[21] G. Perun, J. Warczek, R. Burdzik, Simulation and laboratory studies on the influence of selected engineering and operational parameters on gear transmission vibroactivity. Smart Diagnostics V Book Series: Key Engineering Materials, 588, 266-275 (2014).

Archives of Metallurgy and Materials

The Journal of Institute of Metallurgy and Materials Science and Commitee on Metallurgy of Polish Academy of Sciences

Journal Information


IMPACT FACTOR 2016: 0.571
5-year IMPACT FACTOR: 0.776

CiteScore 2016: 0.85

SCImago Journal Rank (SJR) 2016: 0.347
Source Normalized Impact per Paper (SNIP) 2016: 0.740

Metrics

All Time Past Year Past 30 Days
Abstract Views 0 0 0
Full Text Views 140 136 12
PDF Downloads 41 40 4