Roughness Influence On Macro- And Micro-Tribology Of Multi-Layered Hard Coatings On Carbon Fibre Polymer Composite

Open access

Abstract

Goal of this work is the investigation of roughness influences on the abrasive wear behaviour of magnetron sputtered multi-layered, low-friction coatings on carbon-fibre reinforced polymers (CFRP). Higher coating roughness at similar CFRP quality was realized by higher deposition rates, leading to increased heat flux to the substrates during deposition. Thermal expansion of the epoxy matrix on the micro scale results in a wavy, wrinkled surface topography. Both in scratch and reciprocal sliding testing against alumina, the friction coefficients are lower for the smooth coatings, but their wear rate is higher due to low-cycle fatigue caused abrasion.

[1] S. Guanhong, H. Xiaodong, J. Jiuxing, et al., Applied Surface Science 257, 7864 (2011).

[2] S.M. Vyawahare, Doctoral dissertation, Wichita State University (2006).

[3] L. Di, B. Liu, J. Song, et al., Applied Surface Science 257, 4272 (2011).

[4] Y.S. Lin, C.H. Hu, C.A. Hsiao, Composites Science and Technology, 71, 1579 (2011).

[5] M. Stueber, H. Holleck, H. Leiste, et al., Journal of Alloys and Compounds 483, 321 (2009).

[6] J.M. Lackner, W. Waldhauser, P. Hartmann, et al., Thin Solid Films 520, 2833 (2012).

[7] J.M. Lackner, W. Waldhauser, C. Ganser, et al., Surface and Coatings Technology 241, 80 (2014).

[8] J.M. Lackner, L. Major, M. Kot, et al., Bulletin of the Polish Academy of Sciences: Technical Sciences 59, 343 (2011).

[9] J.M. Lackner, W. Waldhauser, B. Major, et al., Thin Solid Films 534, 417 (2013).

[10] J. Robertson, Materials Science and Engineering, R: Reports 37, 129 (2002).

[11] A. Grill, Diamond and related materials 8, 428 (1999).

[12] H. Ronkainen, S. Varjus, J. Koskinen, et al.. Wear 249, 260 (2001).

[13] Y. Liu, A. Erdemir, E.I. Meletis, et al., Surface and Coatings Technology 82, 48 (1996).

[14] Y. Pauleau, F. Thiery, Surface and Coatings Technology 180, 313 (2004).

[15] Y. Pauleau, F. Thiery, V. Uglov, et al., Surface and Coatings Technology 180, 102 (2004).

[16] H. Dimigen, H. Hübsch, R. Memming, R.. Applied Physics Letters 50, 1056 (1987).

[17] V.V. Uglova, V.M. Anishchik, Y. Pauleau, et al., Vacuum 70, 181 (2003).

[18] C.A. Charitidis, International Journal of Refractory Metals and Hard Materials 28, 51 (2010).

[19] J.M. Lackner, W. Waldhauser, M. Schwarz, et al., Vacuum 83, 302 (2008).

[20] J.M. Lackner, W. Waldhauser, L. Major, et al., Computational and Structural Biotechnology Journal 6, 1 (2013).

Archives of Metallurgy and Materials

The Journal of Institute of Metallurgy and Materials Science and Commitee on Metallurgy of Polish Academy of Sciences

Journal Information


IMPACT FACTOR 2016: 0.571
5-year IMPACT FACTOR: 0.776

CiteScore 2016: 0.85

SCImago Journal Rank (SJR) 2016: 0.347
Source Normalized Impact per Paper (SNIP) 2016: 0.740

Metrics

All Time Past Year Past 30 Days
Abstract Views 0 0 0
Full Text Views 205 160 11
PDF Downloads 142 117 9