Materials Stress Diagnostics by X-Ray and Acoustic Techniques

Open access


Performed investigations and obtained results concerned the analysis of residual stresses in near-surface areas of coppercorundum (Cu-Al2O3) composite and silicon carbide (SiC) samples. X-ray diffraction and acoustic tomography techniques, as well as the suitable calculation procedures, allowed to locate sample-areas with extreme values of stresses residing in the examined materials. The registered texture-stress characteristics reflects inhomogeneity of the samples structure identified by means of acoustic tomography. Obtained results provide valuable information on anisotropy of physical properties of structural elements produced by the technologies applied to the examined samples.

[1] T.W. Clyne, P.J. Withers, An Introductionto Metal Matrix Composites (Cambrigde University Press, Cambridge 1993).

[2] J. Sobczak, S. Wojciechowski, Współczesne tendencje praktycznego zastosowania kompozytów metalowych. Kompozyty (Composites) 2, 3, 24-37 (2002).

[3] H. Gul, F. Kilic, S. Aslan, A. Alp, H. Akbulut, Characteristics of electro-co-deposited Ni-Al2O3 nano-particlereinforced metal matrix composite (MMC) coatings, Wear 267, 976-990 (2009).

[4] L. Du, B. Xu, S. Dong, H. Yang, X. Wu, Preparation, microstructure and tribological properties of nano-Al2O3/Ni brush plated composite coatings, Surface & Coatings Technology 192, 311-316 (2005).

[5] Crystallographic Databese ICDD, PDF+4 package (2010).

[6] I.C. Noyan, J.B. Cohen, Residual Stresses - Measurement by Diffraction and Interpretation (Springer-Verlag, Berlin 1987).

[7] N.G.H. Mayendorf, P.B. Nagy, S.I. Rokhlin, Nondestructive Materials Characterization with application to Aerospace Materials (Springer-Verlag, Berlin, Heidelberg 2004).

[8] A. Baczmanski, Stress field in polycrystalline materials studied using diffraction and self-consistent modeling (Thesis, AGH UST, Kraków 2005).

[9] L. Lutterotti, P. Scardi, Simultaneous Structure and Size-Strain Refinement by the Rietveld Method, J. Appl. Cryst. 23, 246-252 (1990).

[10] K. Pawlik, Determination of the orientation distribution from pole figures in arbitrarily defined cells. Physica Stat Solidi (B) 134, 477-483 (1986).

[11] K. Kudłacz, Computer program SAM3D (IMIM PAN, Kraków 2009).

[12] A. Reuss, Berechnung der Fliessgenze von Mischkristallen auf Grund der Plastizitätsbedingung für Einkristalle, A. Angew. Math. Mech. 9, 49 (1929).

[13] A. Baczmanski, K. Wierzbanowski, J. Tarasiu k, Models of plastic deformation used for internal stress measurements, Zeitschrift fuer Metallkunde/Materials Research and Advanced Techniques 86, 7, 507-511 (1995).

[14] D.B. Hovis, A. Reddy, A.H. Heuer, X-ray elastic constants for Al2O3, Appl. Phys. Lett. 88, 131910-131913 (2006).


Archives of Metallurgy and Materials

The Journal of Institute of Metallurgy and Materials Science and Commitee on Metallurgy of Polish Academy of Sciences

Journal Information

IMPACT FACTOR 2016: 0.571
5-year IMPACT FACTOR: 0.776

CiteScore 2016: 0.85

SCImago Journal Rank (SJR) 2016: 0.347
Source Normalized Impact per Paper (SNIP) 2016: 0.740

Cited By


All Time Past Year Past 30 Days
Abstract Views 0 0 0
Full Text Views 115 114 5
PDF Downloads 32 31 5