The Influence of Die Approach and Bearing Part of Die on Mechanical-Technological Properties of High Carbon Steel Wires / Wpływ Części Roboczej I Kalibrującej Ciągadła Na Własności Mechaniczno-Technologiczne Drutów Ze Stali Wysokowęglowej

Open access

In this work the influence of the die approach and bearing part of die on mechanical-technological properties of high carbon steel wires has been assessed. The drawing process of φ5.5 mm wires to the final wire of φ2.9 mm was conducted in 6 passes, by means of a multi-die drawing machine Koch type. The drawing speeds in the last passes were: 7 m/s. For wires drawn according to four variants the investigation of mechanical-technological properties has been carried out, in which yield strength, tensile strength, uniform and total elongation, reduction of area, the number of twists and the number of bends were determined. On the basis of numerical analyses wire drawing process, the influence of geometry of die on redundant strain and effective strain has been determined.

The investigations have shown the essential influence of geometry of die on mechanical-technological properties of high carbon steel wires. It has been shown that the increase of strength properties in wires drawn with high die angle is related to the occurrence in their bigger effective strain.

[1] M. Suliga, The influence of the high drawing speed on mechanical-technological properties of high carbon steel wires, Archives of Metallurgy and Materials, Quar­terly 56, 3, Warszawa-Kraków, 823-828 (2011).

[2] J. Łuksza, Elementy ciągarstwa, AGH Uczelniane Wydawnictwo Naukowo Techniczne Kraków (2001).

[3] M. Suliga, The influence of the multipass drawing process in classical and hydrodynamic dies on residual stresses of high carbon steel wires, Archives of Metal­lurgy and Materials Quarterly 56, 4, Warszawa-Kraków, 939-944 (2011).

[4] B. Golis, J.W. Pilarczyk, Z. Błażejowsk i, Druty stalowe, Seria Metalurgia, 35, Wydawnictwo Politechniki Częstochowskiej, Częstochowa (2003).

[5] Z. Steininger, Ciągnienie drutów stalowych, Wyd. ”Śląsk”, Katowice (1976).

[6] J.G. Wistreich, The fundamentals of wire drawing, Metallurgical Reviews 3, 10, 97 (1958).

[7] F. Knap, Naprężenia własne w ciągnionych drutach i wyrobach z drutu, Seria Monografie, 25, Wydawnictwo Politechniki Częstochowskiej, Częstochowa (1991).

[8] B. Pikos, J. Michalczyk, J. Krnać, A. Milenin, J.W. Pilarczyk, Wpływ kształtu części roboczej i kalibrującej ciągadła na siłę ciągnienia oraz własności mechaniczne drutów. (Hutnik -Wiadomości Hutnicze) 1-2, 78-81 (2007).

[9] B. Pikos, J.W. Pilarczyk, F. Knap, J. Krnac, Design of convex, concave and sigmoidal die. Inter­national Technical Conference Global Technologies for Emerging Markets, India, October (2006).

[10] J. Krnać, R. Włudzik, J.W. Pilarczyk, R. Kruzel, Influence of angles of approach and Bering parts of dies on mechanical properties of drawn steel carbon wire, Wire Journal International, 72-77, April (2010).

[11] A.A. Milenin, B.P.B. Gautham, S.C. Goyal, J. Pilarczyk, Z. Muskalski, FEM simulation of wire fracture phenomena during multi-pass drawing, Wire Journal International, 93-99, October (2008).

Archives of Metallurgy and Materials

The Journal of Institute of Metallurgy and Materials Science and Commitee on Metallurgy of Polish Academy of Sciences

Journal Information


IMPACT FACTOR 2016: 0.571
5-year IMPACT FACTOR: 0.776

CiteScore 2016: 0.85

SCImago Journal Rank (SJR) 2016: 0.347
Source Normalized Impact per Paper (SNIP) 2016: 0.740

Cited By

Metrics

All Time Past Year Past 30 Days
Abstract Views 0 0 0
Full Text Views 109 108 9
PDF Downloads 55 54 19