Effect of Tungsten and Molybdenum on the Crystallization, Microstructure and Properties of Silumin 226

Open access

Abstract

The work presents the results of the examinations of silumin 226 as well as a silumin produced on its basis containing a W and Mo addition introduced in the amount of 0.1; 0.2; 0.3 and 0.4% of both elements simultaneously. Investigations of the crystallization process of the silumins by the TDA method were conducted. Also, a microscopic analysis of their microstructure was performed and their basic mechanical properties were determined. Microstructure tests were made on casts produced in an TDA sampler as well as by the pressure method. The investigations exhibited a change in the course of crystallization of the silumin containing 0.3 and 0.4% W and Mo with respect to silumin 226 and the silumin with the addition of 0.1 and 0.2%. The presence of additional phases which did not occur in the case of lower addition contents was established in the silumin containing 0.3-0.4% W and Mo, regardless of the applied casting technology. The tests showed the possibility of increasing the tensile strength Rm, the proof stress Rp0,2 and the unit elongation A of the silumin as a result of a simultaneous introduction of the W and Mo addition. The highest values of Rm, Rp0,2 and A were obtained in the silumins with the additions of these elements within the range of 0.1-0.2% each.

[1] Piątkowski, J. (2013). Influence of overheating temperature on the shape of primary silicon crystals in hypereutectic Al-Si cast alloy. Solid State Phenomena. 203-204, 417-422.

[2] Piątkowski, J. & Gajdzik, B. (2013). Testing phase changes in Al-Si cast alloys with application of thermal analysis and differential calorimetric analysis. Metallurgy. 52(4), 469-472.

[3] Piątkowski, J. & Jabłońska, M. (2014). Analysis of material reliability of AlSi17Cu5 alloy using statistical Weibull distribution. Metallurgy. 53(4), 617-620.

[4] Binczyk, F. & Piątkowski, J. (2003). Crystallization of the silumin AlSi17 with the addition of Cr, Co and Ti. Archives of Foundry Engineering. 3(9), 39-44. (in Polish).

[5] Sahoo, K.L. & Pathak, B.N. (2009). Solidification behaviour, microstructure and mechanical properties of high Fe-containing Al–Si–V alloys. Journal of Materials Processing Technology. 209, 798-804.

[6] Sahoo, K.L., Das, S.K. & Murty, B.S. (2003). Formation of novel microstructures in conventionally cast Al-Fe-V-Si alloys. Materials Science and Engineering. 355(1-2), 193-200.

[7] Alloy Phase Diagrams. ASM Handbook Vol. 3. 1992.

[8] Okamoto, H. (2010). Al-Mo (Aluminum-Molybdenum). Journal of Phase Equilibria and Diffusion. 31(5), 492–493.

[9] Pietrowski, S., Pisarek, B., Władysiak, R., Gumienny, G. & Szymczak, T. (2009). TDA curves of metals alloys and the control of their quality. In Szajnar, J. Progress of the Theory and Practice Foundry, (pp. 345-377), Katowice – Gliwice: PAN.

[10] Pisarek, B.P. (2013). Model of Cu-Al-Fe-Ni Bronze Crystalization. Archives of Foundry Engineering. 13(3), 72-79.

[11] Rapiejko, C., Pisarek, B., Czekaj, E. & Pacyniak, T. (2014). Analysis of the Crystallization of AZ91 Alloy by Thermal and Derivative Analysis Method Intensively Cooled in Ceramic Shell. Archives of Foundry Engineering. 14(1), 97-102.

[12] Kacprzyk, B., Szymczak, T., Gumienny, G. & Klimek, L. (2013). Effect of the Remelting on Transformations in Co-Cr-Mo Prosthetics Alloy. Archives of Foundry Engineering. 13(3), 47-50.

[13] PN-EN 1706:2011. Aluminum and aluminum alloys. Castings. The chemical composition and mechanical properties. (in Polish).

Archives of Foundry Engineering

The Journal of Polish Academy of Sciences

Journal Information


CiteScore 2016: 0.42

SCImago Journal Rank (SJR) 2016: 0.192
Source Normalized Impact per Paper (SNIP) 2016: 0.316

Cited By

Metrics

All Time Past Year Past 30 Days
Abstract Views 0 0 0
Full Text Views 110 105 5
PDF Downloads 48 47 5