The sieves’ manufacturers that want to be competitive at the market must have the implemented quality control system. Different methods, based on taking the sample, which is a representative of the total quantity of the forming sieves production, are applied for evaluation of the sieve’s conformity. The basic characteristics of this type of the quality function are control, measuring and testing of the forming sieves’ properties at the end of the manufacturing process. The objective is to detect and separate the products that deviate from the set criteria, to remain in the factory, then to be repaired if possible or discarded in the opposite case and thus to prevent delivery of the defective sieves to the paper manufacturers.
This is a study of a medical injection factory-Babylon carried out in order to achieve proper mechanical and morphological properties, PP has been injection molded by using cold runner injection molding machine with temperature variation (198, 200, 203……220°C) for ten samples. The physical and mechanical properties of PP product were examined. It has been found that the Shore hardness decreases linearly with injection molding temperature increasing. The tensile strength has a similar behavior to the hardness. However, it has been found that the MIF (Melt Index Flow) rates increases with the increase of injection molding temperature. The density of PP has been found for both virgin PP and the samples, it has been found that the density decreases with increasing operation temperature. FTIR (Fourier Transmission Infrared) spectra were taken for both samples with high and low operation temperature. Besides the SEM (Scanning Electronic Microscopy) test shows the difference in the morphology of the product surface and the PP product at high and low operation temperature. Moreover, for all these properties, the PP product exhibits good mechanical properties (hardness, tensile strength, density) for the samples produced at temperature lower than 207°C. While the physical properties such as MIF improved with injection temperature increasing, additionally, the SEM images show that the sample produced in low temperature have surface damage.
Katarína Stachová, Zdenko Stacho, Zuzana Papulová and Marek Jemala
The need for adaptation to rapid changes in the business environment, both on the part of employees and employers, implies dealing with new challenges, acquisition of new knowledge and skills and assumption of new roles and responsibilities. The base for companies is the availability of qualified human resources, which is ensured by the human resource management department mainly through an effective process of employee selection. The paper is oriented at the analysis of the current state of focus of organizations operating in Slovakia on systematicity and complexity of the selection process, the existence of an effective internal labor market and the regularity of development of used selection tools in the context of technological progress and changes in labor market requirements in regions of Slovakia. Results of the survey on (n = 343) enterprises show a positive trend, an increase of more than 10 percent in the orientation towards improvement of the process of employee selection, but on the other side it also confirm an increase in disparities between individual regions of Slovakia, some regions (Eastern Slovakia) progress much slower than the developed ones (Bratislava).
The article presents the results regarding the elimination of constraints in the production process of a power equipment subassembly, a boiler chamber, together with an analysis of the benefits resulting from this, both financial and non-financial. The significance of bottlenecks in the production process, ways of its identification and limitations - in general - are presented. The article is a case-study of an attempt to eliminate the bottleneck in the production process of the boiler chamber, which turned out to be the process of drilling and marking-off, and work stations representing these processes. In order to eliminate the limitation, it was decided to replace the existing tracing and drilling work with a numerically controlled device - a boring machine moved from the liquidated department.. As a result, labor-intensive, manual chambers marking-off and the process of drilling holes with a smaller diameter drill have been eliminated. A number of benefits has been demonstrated resulting from the elimination of the bottleneck in the process, first of all, it was possible to reduce the duration of the marking-off and drilling operations and reduce the costs of the boiler chamber production process.
Renata Nováková, Jana Šujanová and Natália Nováková
The National Quality Programme of the Slovak Republic for 2017-2021 strongly emphasises the primary objectives and priorities of the Quality Improvement Strategy. This should be one of the main priorities of the Slovak Government in the upcoming period. The Quality Improvement Strategy should, in general, lead to an improvement in the quality of life. The aim of the paper is to point out the opportunities for improvement by applying indicators aimed at defining the excellence of organisations within the national economy of the Slovak Republic.
The construction industry in India is the second most important contributor to its gross domestic product. However, high rate of accidents and fatalities have tarnished the image of industry in India. Although the industry contributes significantly to the Indian economy, safety management is the primary concern alongside with frequent workplace accidents. The role of safety management is vital to improve safety performance of an organization. The functions of safety management include planning, organizing, staffing, directing, controlling and coordinating safety activities with an aim to minimize accidents/injuries. Safety trainings, employee participation, compliance of safety procedures and motivational schemes are part of safety management which influences the overall safety performance. Several metrics were developed to measure the safety performance of an organization but not a single measure will reflect the overall performance. The present study considered parameters pertaining to the safety management which have influence on the safety performance of a construction organization in India. The parameters are analyzed by formulating a goal programming model. The results of the study suggests that much improvement is needed in the area of safety trainings and the revised targets were established.
Presented paper concentrate on problems connected with the role of operation manager within industrial company. Operation management concentrate many activities in today’s industrial corporation and because of that the role of it’s manager is very important. He should to have many skills described in this paper. We analysed responsibilities of the operation manager, his basic operational skills and also give some examples of duties and responsibilities of good operation manager on the example of food industry. This example can give some remarks about practical skills needed in operation management in particular enterprise.
The paper concentrates on the issues of applying smart technologies in the manufacturing processes. The author includes in it brief descriptions of the smart technologies that contributed to the emergence of Industry 4.0 concept. Additionally, based on reports and surveys conducted on a global scale regarding the application of intelligent technologies, the author analyses the current state of implementing these technologies in manufacturing processes and provides forecasts regarding the adoption of the solutions based on Artificial Intelligence in global enterprises in the near future.
František Nový, Otakar Bokůvka, Libor Trško and Michal Jambor
In this paper the authors introduce their own selected experimental results in the field of the investigation of fatigue resistance of structural steels. The experiments were carried out on the nine structural steels including high strength steels, DOMEX 700MC, HARDOX 400, HARDOX 450, 100Cr6 (UTS from 446 MPa to 2462 MPa) at high-frequency cyclic loading (f = 20 kHz, T = 20 ± 5 °C, R = -1) in the region of number cycles ranged from N ≈ 2×106 to N ≈ 2×109 cycles of loading. The continuous decrease of fatigue strength in dependence on the number of loading cycles was observed with the average value of ratio σa2×109/σa2×106 = 0.69.
As part of continuous quality improvement in well-managed enterprises, identifying unconformity should initiate actions to find their causes. Therefore, it was proposed to the enterprise located in Podkarpacie to use in the sequential way the Ishikawa diagram and 5Why method. The aim was to analyse of unconformity (porosity cluster) on the turbine outlet nozzle and identify the root of its creation. In the enterprise, the quality analysis of the products with a fluorescent method was carried out, but after identifying the unconformity, non-analysis of their reason for their occurrence was not practiced. Therefore, it was intentional to propose the use of sequence i.e. Ishikawa diagram and 5Why method to identify the root of unconformity. The subject of study was the turbine outlet nozzle, on which the fluorescent method the porosity cluster was identified. With the use of the Ishikawa diagram, the main cause of the problem was pointed (unconformity during production), and by the 5Why method the root cause of the problem, i.e. unconformity material from the supplier, was identified. The proposed method sequence is a simple and effective way to make analyses of unconformities and it can be used in different products and service enterprises.