Przemysław Fiołek, Jacek Jakubowski and Kamil Tomczak
Steel structures for a conveyance guiding system are subjected to prolonged, intense corrosion during their operation leading to a considerable loss of material and structure capacity reduction. Shaft guides are made of closed profiles welded from hot-rolled channel sections. These profiles are categorized as class 1 cross-sections according to Eurocode 3, which means that they are resistant to local instability upon bending . With an increase in the corrosion loss of the guides, the inertia moment of the cross-section is reduced. The resistance of profiles to local buckling is also reduced. However, calculations for local stability in guides upon bending are not required by the local Polish regulations on the operation of conveyance in shafts . The question is whether this constitutes a shortcoming and risk for safe operation. Calculations according to steel construction standards  supported by numerical simulation were used to evaluate shaft steelwork guides resistance to buckling and their sensitivity to corrosion loss. It was shown that the guides of corrosion loss of 52–63%, depending on profile size, are prone to local buckling.
The paper presents the identification methodology of anisotropic criteria based on triaxial test results. The considered material is varved clay – a sedimentary soil occurring in central Poland which is characterized by the so-called “layered microstructure”. The strength examination outcomes were identified by standard triaxial tests. The results include the estimated peak strength obtained for a wide range of orientations and confining pressures. Two models were chosen as potentially adequate for the description of the tested material, namely Pariseau and its conjunction with the Jaeger weakness plane. Material constants were obtained by fitting the model to the experimental results. The identification procedure is based on the least squares method. The optimal values of parameters are searched for between specified bounds by sequentially decreasing the distance between points and reducing the length of the searched range. For both considered models the optimal parameters have been obtained. The comparison of theoretical and experimental results as well as the assessment of the suitability of selected criteria for the specified range of confining pressures are presented.
In the case of a two-phase medium – such as the soil, which consists of an elastic skeleton and is filled with pore fluids – stress and strain within the medium are dependent on both phases. Similarly, in the case of heat transfer, heat is conducted through the two phases at different rates, with an additional heat transfer between the phases. In the classical approach to modelling a porous medium, it is assumed that the fluid filling the pore space is water, which is incompressible. In the case of gas, the volume of which is strongly dependent on temperature and pressure, one should take this behavior into account in the constitutive relations for the medium. This work defines the physical relations of a two-phase medium and provides heat transfer equations, constructed for a porous, elastic skeleton with fluid-filled pores, which may be: liquid, gas, or mixture of liquid and a gas in non-isothermal conditions. The paper will present constitutive relations derived from the laws of irreversible thermodynamics, assuming that pores are filled with either a liquid or a gas. These relations, in the opinion of the authors, may be used as the basis for the construction of a model of the medium filled partly with a liquid and partly with a gas. It includes the possibility of independent heat transfer through any given two-phase medium phase, with the transfer of heat between the phases.
The paper presents the characteristics of seismic tremors and rockbursts that occurred between 2001 and 2015. The characteristics are based on a general description of the geological structure of the Upper Silesian Coal Basin (USCB). The level of seismic activity in the analysed period changed a number of times and depended on the intensity of mining works and diverse mining and geological conditions in each of the five regions where tremors occurred (Bytom Trough, Main Saddle, Main Trough, Kazimierz Trough, and Jejkowice and Chwałowice Troughs) and which belong to various structural units of the Upper Silesia. It was found out that in the case of rockbursts the phenomena were recorded in three regions. These are: Main Saddle, Bytom Trough, and Jejkowice and Chwałowice Troughs. The so called Regional Rockburst Indicator (RWT) was estimated for each of the regions where the rockbursts had been recorded. The obtained values of RWT are presented against the Probability of RockBurst (PT) in a given area.
Static load tests on foundation piles are generally carried out in order to determine load – the displacement characteristic of the pile head. For standard (basic) engineering practices this type of test usually provides enough information. However, the knowledge of force distribution along the pile core and its division into the friction along the shaft and the resistance under the base can be very useful. Such information can be obtained by strain gage pile instrumentation . Significant investigations have been completed on this technology, proving its utility and correctness , , . The results of static tests on instrumented piles are not easy to interpret. There are many factors and processes affecting the final outcome. In order to understand better the whole testing process and soil-structure behavior some investigations and numerical analyses were done. In the paper, real data from a field load test on instrumented piles is discussed and compared with numerical simulation of such a test in similar conditions. Differences and difficulties in the results interpretation with their possible reasons are discussed. Moreover, the authors used their own analytical solution for more reliable determination of force distribution along the pile. The work was presented at the XVII French-Polish Colloquium of Soil and Rock Mechanics, Łódź, 28–30 November 2016.
The effect of magnetic field dependent (MFD) viscosity on thermal convection in a horizontal ferromagnetic fluid layer has been investigated numerically. A correction is applied to Sunil et al.  which is very important in order to predict the correct behavior of MFD viscosity. Linear stability analysis has been carried out for stationary convection. The MFD viscosity parameter δ as well as the measure of nonlinearity of magnetization M3, both have a stabilizing effect on the system. Numerical results are also obtained for large values of magnetic parameter M1 and predicted graphically.
Paweł Ciężkowski, Jan Maciejewski and Sebastian Bąk
This paper presents experimental comparison of two machine crushing technologies: one-stage and two-stage. The study was carried on a model double-toggle jaw crusher which allows crushing forces, energy and toggle displacement to be measured. The main aim of the work was to determine the energy consumption of crushing process assuming a given level of fragmentation. Studies were performed on three rocks: granite “Strzegom”, limestone “Morawica” and sandstone “Mucharz”. The material tested had a cubic shape and average dimension of 90 mm. One-stage crushing was carried out for outlet slot er = 11 mm, and two-stage crushing for er = 24 mm and 11 mm. In the tests special design of variable profile moving jaw was used and fixed jaw was flat. The analysis of the results shows that taking into account energy consumption, it is better to use two-stage crushing process. For given materials energy consumption in the two-stage crushing process was reduced by 30%.
Karolina Adach-Pawelus, Jan Butra and Daniel Pawelus
Experience gained until now underground mining worldwide and in Poland indicates that remnants may have an impact on the occurrence of seismic phenomena. Remnants are stress concentration sites encompassing both the deposit and the layers of rock mass located above and below the undisturbed rock. In the case where stresses in the remnant exceed its strength, it may collapse, and under unfavourable geomechanical conditions, stress-induced rockburst may occur. Remnants may also cause breaking of strong roof layers above their edges, which results in the occurrence of high-energy shocks (Salustowicz , Adach , Adach and Butra ). This article presents the possibility of utilizing numerical modeling to evaluate the influence of remnant upon the occurrence of seismic phenomena. The results of numerical calculations performed for a model room-and-pillar mining system with roof deflection under the conditions of copper ore mines in the Legnica-Głogów Copper District (LGOM) are presented. Numerical calculations in a plane strain state were performed by means of Phase2 v. 8.0 software for the analyzed mining system in which remnant was left behind. The results of numerical modeling showed that sudden fracturing of roof layers above the mined out space may occur on the edge of the remnant. This may cause a shock with very high energy, and under the appropriate conditions, this may lead to the rockburst phenomenon.
Salt was excavated at the “Wieliczka” Salt Mine for over 700 years. Underground mining operations terminated in 1996, by which time almost 2,400 chambers and 245 km of galleries had been created underground, situated on 9 levels and a few interlevels. In 1978, the mine was included in the UNESCO World Heritage List, which stated that parts of the mine with historical value had to be preserved for future generations. In order to preserve the most valuable chambers and galleries, activities aimed at establishing a protection pillar for excavations were conducted in the conservation area on Levels I-V. The need of large scope preserving works created the necessity to conduct a new and truly comprehensive geomechanical analysis. Such an analysis could only be done by means of advanced numerical modelling codes. Three-dimensional calculations were performed by means of FLAC 3D finite difference code. Rock mass stability assessment in the vicinity of excavations was carried out on the basis of the distribution and range of the so called failure zones. This comprehensive geomechanical analysis allows for verification and give the directions for future preservation and closure works in the “Wieliczka” mine.
Kamil Tomczak, Jacek Jakubowski and Przemysław Fiołek
Crack width measurement is an important element of research on the progress of self-healing cement composites. Due to the nature of this research, the method of measuring the width of cracks and their changes over time must meet specific requirements. The article presents a novel method of measuring crack width based on images from a scanner with an optical resolution of 6400 dpi, subject to initial image processing in the ImageJ development environment and further processing and analysis of results. After registering a series of images of the cracks at different times using SIFT conversion (Scale-Invariant Feature Transform), a dense network of line segments is created in all images, intersecting the cracks perpendicular to the local axes. Along these line segments, brightness profiles are extracted, which are the basis for determination of crack width. The distribution and rotation of the line of intersection in a regular layout, automation of transformations, management of images and profiles of brightness, and data analysis to determine the width of cracks and their changes over time are made automatically by own code in the ImageJ and VBA environment. The article describes the method, tests on its properties, sources of measurement uncertainty. It also presents an example of application of the method in research on autogenous self-healing of concrete, specifically the ability to reduce a sample crack width and its full closure within 28 days of the self-healing process.