E. E. Doğan, P. Tokcan, M. E. Diken, B. Yilmaz, B. K. Kizilduman and P. Sabaz
In this study, it was aimed to synthesize hydrogel based antibacterial, biocompatible and non-toxic wound dressing materials by solvent removal method usingpoly(vinylalcohol) (PVA), poly(vinylpyrolidone) (PVP) and nano pomegranate seed (PN).The morphology, swelling capacity, contact angle, antibacterial activity, biocompatibility and cytotoxicity of the synthesized films were determined. From the experimental findings, it was found that the PN particles were nano-sized, showed homogeneous and spherical distribution and improved the hydrophobic properties of the materials obtained by the addition of PN. And also, their swelling capacities were decreased with increased PN amount and all of the materials showed similar antibacterial activity, hemocompatibility and cytotoxicity.
A. Anbarasi, S.M. Ravi Kumar, M. Packiya Raj, G.J. Shanmuga Sundar, M. Ganapathy, T. Kubendiran and S. Varalakshmi
A novel semiorganic nonlinear optical (NLO) crystal, bis(thiourea) barium nitrate (BTBN) was synthesized and grown by slow evaporation method. Structure of the new crystalline compound was confirmed by single crystal X-ray diffraction analysis and it showed that BTBN belongs to orthorhombic crystal system. The crystalline nature of the BTBN was confirmed by powder X-ray diffraction study. Important functional groups of BTBN were identified by FT-IR spectroscopic analysis. UV-Vis-NIR spectral study showed that the grown crystal is transparent in the entire visible region with low cut off wavelength of 304 nm. BTBN exhibits a SHG efficiency which is nearly 2.38 times higher than that of KDP. The BTBN crystal has high mechanical strength and belongs to soft category, which was confirmed by micorhardness study. The thermal stability of BTBN was determined from TGA and DTA thermal study which revealed that the BTBN crystal has thermal stability up to 243.1 °C. The surface properties and presence of elements was analyzed by SEM and EDAX study, respectively.
Stanisław Pikus, Małgorzata Zienkiewicz-Strzałka and Małgorzata Skibińska
The paper presents the new way of preparation of MCF foams with NaY zeolite. Significant changes in the amount of micro and mesopores in relation to the amount of NaY zeolite and 1,3,5-trimethylbenzene (TMB) added during the synthesis was observed. It suggests the possibility of controlling the micro/mesopores ratio by applying the proposed method. Environmental aspects of using new MCF/NaY foams is related to the adsorption of thorium ions (Th+4). The term of “MCF/NaY materials” refers to the general name of the material without referring to the content and state of zeolite. The obtained materials were highly effective in relation to Th+4. The adsorption capacity was greater when the number of micropores was lower. The dependence of adsorption capacity of Th+4 ions on aluminum atoms content was also confirmed.
Chunyu Deng, Chaoran Qin, Xinyi Li, Shaoqing Li, Zhixiong Huang, Lianmeng Zhang, Xuedong Zhou, Dongyun Guo and Yang Ju
PbZr0.52Ti0.48O3 nanocrystals were synthesized by a hydrothermal method. The effect of NaOH concentration, reaction temperature and time on nucleation and growth of PbZr0.52Ti0.48O3 nanocrystals was investigated. As the 0.05 mol/L PbZr0.52Ti0.48O3 precursors were heated at 200 °C for 21 h with NaOH concentration of 0.5 mol/L, the tetragonal PbZr0.52Ti0.48O3 nanocrystals were formed, and the grain size was more than 20 nm. With increasing the NaOH concentration from 0.5 to 1.5 mol/L, the grain size of PbZr0.52Ti0.48O3 nanocrystals decreased. When the precursors were heated at different temperatures (140 °C to 200 °C) for 21 h with 1.0 mol/L NaOH, single-phase PbZr0.52Ti0.48O3 nanocrystals were obtained at 160 °C to 200 °C. With increasing the reaction temperature from 160 °C to 200 °C, the grains size of PbZr0.52Ti0.48O3 nanocrystals increased from 5 nm to 9 nm. When the precursors were heated at 160 °C in different reaction times from 6 h to 21 h, the evolution from amorphous to crystalline PbZr0.52Ti0.48O3 nanocrystals in correlation with the reaction time was observed. Single crystalline PbZr0.52Ti0.48O3 nanocrystals with narrow size distribution (from 5 nm to 9 nm) were synthesized by controlling the NaOH concentration, reaction temperature and time. The obtained results can find potential application in preparing PbZr0.52Ti0.48O3 thin films on flexible substrates.
Simulated transmission spectra for tapered fibers with no taper, one taper and two tapers in the near infrared wavelength range, calculated by Finite-Difference-Time-Domain method are currently presented. Transmission peak positions tend to shift to the shorter wavelength when the taper deformation is added to the fiber or the taper width gets narrower. The thickness sensitivity for the tapered structures with different taper thicknesses is about 2.28e-3 nm·µm−1. There is an interference structure in the electric field distribution images, which reveals in the fiber structures. The transmission spectra for the fiber without taper, one taper and two-tapered structures were simulated in near infrared wavelength by FDTD. The transmission spectra for tlated in near infrared wavelength by FDTD. The sensitivity of the fiber was about 50 nm × RIU−1 and it had better refractive index detection. The tapered fiber can be applied to the bio-chemical sensors and physical deformation testing.
As part of continuous quality improvement in well-managed enterprises, identifying unconformity should initiate actions to find their causes. Therefore, it was proposed to the enterprise located in Podkarpacie to use in the sequential way the Ishikawa diagram and 5Why method. The aim was to analyse of unconformity (porosity cluster) on the turbine outlet nozzle and identify the root of its creation. In the enterprise, the quality analysis of the products with a fluorescent method was carried out, but after identifying the unconformity, non-analysis of their reason for their occurrence was not practiced. Therefore, it was intentional to propose the use of sequence i.e. Ishikawa diagram and 5Why method to identify the root of unconformity. The subject of study was the turbine outlet nozzle, on which the fluorescent method the porosity cluster was identified. With the use of the Ishikawa diagram, the main cause of the problem was pointed (unconformity during production), and by the 5Why method the root cause of the problem, i.e. unconformity material from the supplier, was identified. The proposed method sequence is a simple and effective way to make analyses of unconformities and it can be used in different products and service enterprises.
Solid polymer electrolytes based on polyvinyl alcohol (PVA) doped with LiPF6 have been prepared using solution casting technique. Electrical properties of prepared electrolyte films were analyzed using AC impedance spectroscopy. The ionic conductivity was found to increase with increasing salt concentration. The maximum conductivity of 8.94 × 10−3 S·cm−1 was obtained at ambient temperature for the film containing 20 mol% of LiPF6. The conductivity enhancement was correlated to the enhancement of available charge carriers. The formation of a complex between the polymer and salt was confirmed by Fourier transform infrared spectroscopy (FT-IR). The optical nature of the polymer electrolyte films was analyzed through UV-Vis spectroscopy.
The main issue of the paper is the estimation of soil hydraulic permeability based on the DMT test. DMTA, DMTC and SASK methods performed in the Nielisz dam, Stegny and the SGGW Campus of the Warsaw University of Life Sciences sites are described. The article presents the implementation of the dilatometer Marchetti test (DMT) in the determination of soil fraction and effects of its occurrence in the subsoil, tested in the Nielisz dam located in the Wieprz river valley in the Lublin province, and in various sites in Warsaw (Stegny site and SGGW Campus of the Warsaw University of Life Sciences). In order to acquire the needed data, the flat dilatometer test (DMT) method was used. A direct and indirect pressure methodology of interpreting soil swelling was characterized in the article. The paper shows the possibilities of determining sand, silt and clay soil fractions based on po and p1 pressures from dilatometer tests (DMT) and the effective (σ’vo) and total (σvo) vertical in situ overburden stress. Additionally, the main advantage of this paper is the proposal of use of a new chart to determine hydraulic permeability and soil fraction, based on DMT tests.
Kheira Boutouba, Ismail Benessalah, Ahmed Arab and Ahmed Djafar Henni
Sands reinforced by hydraulic binders (cement) have constituted in recent decades a major asset for the expansion of several areas of engineering. The mechanical behavior of sand-cement mixtures has undergone some controversies studied on the Chlef sand. In this paper, we present an experimental study to investigate the mechanical behavior of a sandy soil reinforced by a hydraulic binder (cement), using the direct shear apparatus emphasizing on the shear strength characteristics and the vertical deformation variation of cemented reinforced sand. The parameters used in this study are mainly: relative density (Dr = 80%), normal stress (σn = 100, 200, 400 kPa), water content (3, 7 and 10%), cement content (2.5, 5, 7.5 and 10 %) and cure time (7, 14 and 28 days). The experimental results show that the mechanical characteristics in terms of internal cohesion (C) and internal frication angle (φ) give a better mechanical performance with the binder inclusion, and the cure conditions play an effective role on the improvement of the shear strength. This result also showed that 10% of the cement content gave us a maximum value of shear strength and an optimal influence on the mechanical characteristics. The addition of cement not only improves the shear strength of soil, but also provides diversity in the resistance against the deformations imposed load, which can be established by a dilatant character.
C. Iheduru, M. A. Eleruja, B. Olofinjana, O. E. Awe and A.D.A Buba
We have explored the effectiveness of Geant4 by using it to simulate phonon conduction in Sn Host with Si Nanowire Interface. Our Monte Carlo Simulation shows that the effectiveness of the phonon conduction Geant4 simulation increases when the system attained a steady state of 100 time steps. We have simulated phonon conduction in Sn host with Si nanowire interface using a Geant4Condensed Matter Physics Monte Carlo simulation toolkit in a low cost and less powerful processing computer machine. In the simulation, phonons were displaced inside a computation domain from their initial positions with the velocities and direction vectors assigned to them. A time step was selected so that a phonon can move at most the length of one sub-cell in one time step. Our phonon conduction analysis of SiSn based alloy using Geant4 showed performance enhancement and reasonable predicted thermal values. Numerical predictions of the thermal profile simulations of the values of the temperature in each cell were all within ten percent of the average temperature of Silicon – Tin.