Continuous gas-lift in a typical oil well was simulated using computational fluid dynamic (CFD) technique. A multi fluid model based on the momentum transfer between liquid and gas bubbles was employed to simulate two-phase flow in a vertical pipe. The accuracy of the model was investigated through comparison of numerical predictions with experimental data. The model then was used to study the dynamic behaviour of the two-phase flow around injection point in details. The predictions by the model were compared with other empirical correlations, as well. To obtain an optimum condition of gas-lift, the influence of the effective parameters including the quantity of injected gas, tubing diameter and bubble size distribution were investigated. The results revealed that increasing tubing diameter, the injected gas rate and decreasing bubble diameter improve gas-lift performance.
The present work presents a new approach based on neural network prediction for simple and fast estimation of the creep plastic behaviour of the short fiber composites. Also, this approach is proposed to reduce the solution procedure. Moreover, as a significant application of the method, shuttles and spaceships, turbine blades and discs are generally subjected to the creep effects. Consequently, analysis of the creep phenomenon is required and vital in different industries. Analysis of the creep behaviour is required for failure, fracture, fatigue, and creep resistance of the optoelectronic/photonic composites, and sensors. One of the main applications of the present work is in designing the composites with optical fibers and devices. At last, a good agreement is seen among the present prediction by neural network approach, finite element method (FEM), and the experimental results.
Isogeometric Analysis (IGA) involves unification of modelling and analysis by adopting the same basis functions (splines), for both. Hence, spline based parametric model is the starting step for IGA. Representing a complex domain, using parametric geometric model is a challenging task. Parameterization problem can be defined as, finding an optimal set of control points of a B-spline model for exact domain modelling. Also, the quality of parameterization, too has significant effect on IGA. Finding the B-spline control points for any given domain, which gives accurate results is still an open issue. In this paper, a new planar B-spline parameterization technique, based on domain mapping method is proposed. First step of the methodology is to map an input (non-convex) domain onto a unit circle (convex) with the use of harmonic functions. The unique properties of harmonic functions: global minima and mean value property, ensures the mapping is bi-jective and with no self-intersections. Next step is to map the unit circle to unit square to make it apt for B-spline modelling. Square domain is re-parameterized by using conventional centripetal method. Once the domain is properly parameterized, the required control points are computed by solving the B-spline tensor product equation. The proposed methodology is validated by applying the developed B-spline model for a static structural analysis of a plate, using isogeometric analysis. Different domains are modelled to show effectiveness of the given technique. It is observed that the proposed method is versatile and computationally efficient.
Thermal instability in a horizontal layer of Couple-stress nanofluid in a porous medium is investigated. Darcy model is used for porous medium. The model used for nanofluid incorporates the effect of Brownian diffusion and thermophoresis. The flux of volume fraction of nanoparticle is taken to be zero on the isothermal boundaries. Normal mode analysis and perturbation method is employed to solve the eigenvalue problem with the Rayleigh number as eigenvalue. Oscillatory convection cannot occur for the problem. The effects of Couple-stress parameter, Lewis number, modified diffusivity ratio, concentration Rayleigh number and porosity on stationary convection are shown both analytically and graphically.
The effect of three different factors, which are inflation pressure, vertical load and coefficient of friction on the natural frequencies of a tire (175/70 R13) has been studied. A three dimensional tire model is constructed, using four different material properties and parts in the tire. Mechanical properties of the composite parts are evaluated. After investigating the free vibration, contact analysis is carried out. A concrete block and the tire are modelled together, using three different coefficients of friction. Experiments are run under certain conditions to check the accuracy of the numerical model. The natural frequencies are measured to describe free vibration and vibration of the tire contacted by ground, using a damping monitoring method. It is seen, that experimental and numerical results are in good agreement. On the other hand, investigating the impact of three different factors together is quite difficult on the natural frequencies. When some of these factors are assumed to be constant and the variables are taken one by one, it is easier to assess the effects.
The exact solutions of a nonlinear differential equations system, describing the boundary layer flow over a stretching sheet with a convective boundary condition and a slip effect have been obtained in this paper. This problem has been numerically solved by using the shooting method in literature. The aim of the current paper is to check the accuracy of these published numerical results. This goal has been achieved via first obtaining the exact solutions of the governing nonlinear differential equations and then, by comparing them with the approximate numerical results reported in literature. The effects of the physical parameters on the flow field and the temperature distribution have been re-investigated through the new exact solutions. The main advantage of the current paper is the simple computational approach that has been introduced to analyze exactly the present physical problem. This simple analytical approach can be further applied to investigate similar problems. Although no remarkable differences have been detected between the current figures and those obtained in literature, the authors believe that if some numerical calculations were available for the fluid velocity and the temperature in literature then the convergence criteria and the accuracy of the shooting method used in Ref.  can be validated in view of the current exact expressions.
The paper presents a geometrical approach to dynamics simulation of a rigid and flexible system, compiled of high speed rotating machine with eccentricity and considerable inertia and mass. The machine is mounted on a vertical flexible pillar with considerable height. The stiffness and damping of the column, as well as, of the rotor bearings and the shaft are taken into account. Non-stationary vibrations and transitional processes are analyzed. The major frequency and modal mode of the flexible column are used for analytical reduction of its mass, stiffness and damping properties. The rotor and the foundation are modelled as rigid bodies, while the flexibility of the bearings is estimated by experiments and the requirements of the manufacturer. The transition effects as a result of limited power are analyzed by asymptotic methods of averaging. Analytical expressions for the amplitudes and unstable vibrations throughout resonance are derived by quasi-static approach increasing and decreasing of the exciting frequency. Analytical functions give the possibility to analyze the influence of the design parameter of many structure applications as wind power generators, gas turbines, turbo-generators, and etc. A numerical procedure is applied to verify the effectiveness and precision of the simulation process.
Nonlinear and transitional effects are analyzed and compared to the analytical results. External excitations, as wave propagation and earthquakes, are discussed. Finite elements in relative and absolute coordinates are applied to model the flexible column and the high speed rotating machine. Generalized Newton - Euler dynamics equations are used to derive the precise dynamics equations. Examples of simulation of the system vibrations and nonstationary behaviour are presented.
The article proposes the solution of the problem with the application of thermal vibrations of heat-carrier flow in processes of convective drying, for the purpose of theoretical determination of optimum conditions of short-term excess of handling temperature, that do not influence the decrease of technological characteristics of the thermosensitive materials.
Isogeometric Analysis (IGA) is a new analysis method for unification of Computer Aided Design (CAD) and Computer Aided Engineering (CAE). With the use of NURBS basis functions for both modelling and analysis, the bottleneck of meshing is avoided and a seamless integration is achieved. The CAD and computational geometry concepts in IGA are new to the analysis community. Though, there is a steady growth of literature, details of calculations, explanations and examples are not reported. The content of the paper is complimentary to the existing literature and addresses the gaps. It includes summary of the literature, overview of the methodology, step-by-step calculations and Matlab codes for example problems in static structural and modal analysis in 1-D and 2-D. At appropriate places, comparison with the Finite Element Analysis (FEM) is also included, so that those familiar with FEM can appreciate IGA better.
Elastic wave scattering by cracks at macro- and nano-scale in anisotropic plane under conditions of plane strain is studied in this work. Furthermore, time-harmonic loads due to incident plane longitudinal P- or shear SV- wave are assumed to hold. In a subsequent step, the elastodynamic fundamental solution for general anisotropic continua derived in closed-form via the Radon transform is implemented in a numerical scheme based on the traction boundary integral equation method (BIEM). The surface elasticity effect in the case of nano-crack is taken into consideration via non-classical boundary condition along the crack surface proposed by Gurtin and Murdoch . The numerical results obtained herein reveal substantial differences between anisotropic materials containing a macro- and a nano-crack in terms of their dynamic stress response, where the latter case demonstrates clearly the strong influence of the size-effects. Finally, these types of examples serve to illustrate the present approach and to show its potential for evaluating the stress concentration fields (SCF) inside cracked nanocomposites. The obtained results concern the reliability and safety of the advancing nanomaterials.