As part of continuous quality improvement in well-managed enterprises, identifying unconformity should initiate actions to find their causes. Therefore, it was proposed to the enterprise located in Podkarpacie to use in the sequential way the Ishikawa diagram and 5Why method. The aim was to analyse of unconformity (porosity cluster) on the turbine outlet nozzle and identify the root of its creation. In the enterprise, the quality analysis of the products with a fluorescent method was carried out, but after identifying the unconformity, non-analysis of their reason for their occurrence was not practiced. Therefore, it was intentional to propose the use of sequence i.e. Ishikawa diagram and 5Why method to identify the root of unconformity. The subject of study was the turbine outlet nozzle, on which the fluorescent method the porosity cluster was identified. With the use of the Ishikawa diagram, the main cause of the problem was pointed (unconformity during production), and by the 5Why method the root cause of the problem, i.e. unconformity material from the supplier, was identified. The proposed method sequence is a simple and effective way to make analyses of unconformities and it can be used in different products and service enterprises.
Wheat kernel is made up of structures of different apparent viscosities with varied ability to withstand stress and dissipate strain energy. Its complex mechanical behaviour determines technological susceptibility and is important for wheat quality assessment. The aim of the study was the examination of the Peleg and Normand model to characterize the overall stress relaxation behaviour of wheat kernel at varying loading conditions. The relaxation experiments were made with a help of a universal machine Zwick Z020 in compression at four distinct initial load levels, i.e., 20, 30, 40, and 50 N. The measurements were made for intact wheat kernels at seven levels of moisture content. Relaxation characteristics were approximated with the help of Peleg and Normand formula. An interactive influence of the load level and moisture on Peleg and Normand constants have been confirmed. The initial loading level had none or only slight effect on the model coefficients (Y(t), k1 and k2). The parameters of the Peleg and Normand model decreased with the increase of water content in kernels. For moist kernels, a higher amount of absorbed compression energy was relaxed, since less energy was necessary to keep the deformation at a constant level.
Jasna Tolmac, Slavica Prvulovic, Marija Nedic and Dragisa Tolmac
The paper analyzes the development opportunities of solar systems in the Republic of Serbia. Renewable energy sources and their energy potential, such as solar energy, should be considered in order to meet the needs of consumers. Solar energy can be considered the most modern renewable energy whose utility is still developing, and it is not represented as the utilization of hydro energy sources. Researches show that Serbia is a country with a high RES potential and that it has favorable conditions for production of electrical and heat energy from renewable sources. The aim of this paper is to present the possibilities of using solar energy in Serbia. Energy supply from renewable energy sources is a key factor for each country's strategy, because it directly contributes to reducing the negative effect on the environment.
A photocode in Polish is a common name for a two-dimensional code, which is characterized by higher information capacity than a traditional barcode. The paper analyses the use of the two-dimensional coding system - DataMatrix to identify and classify the material stream in the production process. The analysis showed the effectiveness of the implementation of the coding system in the context of increased availability, machine use and increased product quality. The improvement in the production process is confirmed by an increase in the OEE index. As part of further improvement measures, the coding system should be implemented throughout the enterprise, its compatibility with existing systems should be ensured and applied to all products.
Stanisław Parafiniuk, Alaa Kamel Subr, Marek Milanowski and Anna Krawczuk
Three different types of nozzles (different wear rate) were used in this study. They are classified depending on the severity of their wear to three groups: new, worn and damaged nozzles. Those nozzles were spraying with the same application rate (303 l/ha) on two-year field trials; this was achieved by changing the spraying pressure for each group of nozzles in order to get the same application rate. This practice is usually done by operators of sprayers, who calibrate the sprayers on the same application rate every year without changing the nozzles, so they tend to reduce the spraying pressure in order to compensate the flow rate increase due to the nozzles yearly wear. Two types of plant growth regulators (PGR) agents were used in this study, namely: Moddus and Kelpak, they were applied to wheat plants field to reduce lodging. The results showed that applying PGR in the year 2015 produced an increase in the wheat yield and reduction in the plant height regardless the nozzle type, although there was not any occurrence of wheat lodging. In the year 2016, the new nozzles produced higher values of wheat yield than other two types of nozzles.
This paper presents some aspects of the process of services, products and manufacturing transfer, with the associated production resources, from other locations and plants to Poland.
The study was carried out on the basis of an analysis of publications about delocalization as well as by means of desk research, where there were used the accessible primary and secondary data such as branch reports, statistical data available in reports, data bases, and information accessible on Polish and European websites. The article is also the result of the author's experience of participation in the relocation of a number of international companies, regarding various industries. Delocalization in Poland was presented both from the point of view of Conceptualizing delocalization (literature review, theoretical position) and Implementation of production.
The delocalization mainly takes advantage of labor forces. On the other hand, it may also concern innovative activities and develop high-tech for regions affected by economic restructuring. The social policies for the risk mitigation of the delocalization of production are also being developed and implemented. This work clarifying the conditions of delocalization in Poland and highlight the important roles played by innovation and institutions for achieving sustainability.
The paper presents the coupled electro-mechanical problem. In the numerical analysis of the issue, piezoelectric solid-to-shell transition elements were applied. They combine three-dimensional or hierarchical shell piezoelectric elements with piezoelectric first order elements. The mentioned first order of the element refers to the field of transversal displacements of an element. The mechanical field of the discussed piezoelectric elements may correspond to: the model of three-dimensional theory of elasticity, hierarchical shell models of higher orders or the first order shell model. The electrical field of the potential may be modelled with hierarchical dielectric first order models or higher in transverse direction or with a three-dimensional theory. Effectiveness of modification of algorithms of classical piezoelectric elements was assessed in this paper. To perform such an assessment, curves of convergence of hp method in model tasks are presented. Curves obtained with the use of classical and modified piezoelectric transition elements were set and compared.
In this paper, an outlook about the present of electrical aviation is given. The relatively small energy density of current battery technologies is adequate to build usable electric car, but not suitable for electric aircraft. Because of the very limited amount of energy available on-board, a couple of percent in efficiency can give significant increase in range and flight time, hence the development of more efficient propulsion system and E-motor is as important as the development of battery technologies. Current research results at the University of Dunaujvaros show, that building E-motors from amorphous materials is possible, and can easily increase the efficiency of high speed E-motors.
A short survey is reported on the advantageous and disadvantageous properties of soft magnetic glassy tapes to build stator and rotor elements for the increase of motor efficiency. The relative high saturation magnetization and the relative permeability of these alloy groups seem to be promising in this application field. On the other hand, the sample thickness (30 µm) displays limitations in terms of a filling factor. High hardness of tapes hinders the effectivity of mechanical shaping. Laser cutting can be successful as shaping method, presuming that the extension (thickness) of heat affected zone (HAZ) can be successfully reduced below 50µm, avoiding the brittleness evolution.
Assessment of the colour with the use of many parameters is used with reference to evaluation of the quality changes of products resulting from application of specific technological treatments. The paper investigates the effect of relations between parameters of irradiation of potato bulbs with UVC on selected coefficients of assessment of the colour of fries determined with CIE L*a*b* method. It was statistically significantly proved that UV-C radiation affected brightness of fries, change in colour, recognition of the difference in colour and intensity of the colour reception. Statistical analysis of results was carried out at the assumed level of significance α=0.05.