This article presents the results of the application of Digital Image Correlation (DIC) to measurements of in-plane shear modulus and strength of three different carbon fiber reinforced laminates. Three different approaches to shear strain calculations via DIC are evaluated and compared with standard strain gage measurements. Calculation of shear strain based on averaging DIC strain values of strain gages area in most cases yielded results closest to strain gages, while measurements based on single point strain measuring differed the most from strain gages. These results are attributed to shear strain distribution in the center area of the specimen. Thermoplastic matrix fabric reinforced composite had the lowest shear strength at 5% of shear strain, but the highest ultimate shear strength and strain at failure. Of thermosetting materials, laminate reinforced with unidirectional carbon fiber had shear modulus about 10% lower, than fabric reinforced laminate, but higher ultimate strength and strain at failure. This behavior is attributed to the presence of weaves in fabric reinforcing the laminate, causing shear stiffening of the material, but lowering its ability to deform under shear loading.
The present research is focused on developing ZnAl2O4 (gahnite) spinel as an antireflection coating material for enhanced energy conversion of polycrystalline silicon solar cells (PSSC). ZnAl2O4 has been synthesized using dual precursors, namely aluminum nitrate nonahydrate and zinc nitrate hexahydrate in ethanol media. Diethanolamine has been used as a sol stabilizer in sol-gel process for ZnAl2O4 nanosheet fabrication. ZnAl2O4 nanosheet was deposited layer-by-layer (LBL) on PSSC by spin coating method. The effect of ZnAl2O4 coating on the physical, electrical, optical properties and temperature distribution in PSSC was investigated. The synthesized antireflection coating (ARC) material bears gahnite (ZnAl2O4) spinel crystal structure composed of two dimensional (2D) nanosheets. An increase in layer thickness proves the LBL deposition of ARC on the PSSC substrate. The ZnAl2O4 2D nanosheet comprising ARC on the PSSC was tested and it exhibited a maximum of 93 % transmittance, short-circuit photocurrent of 42.364 mA/cm2 and maximum power conversion efficiency (PCE) 23.42 % at a low cell temperature (50.2 °C) for three-layer ARC, while the reference cell exhibited 33.518 mA/cm2, 15.74 % and 59.1 °C, respectively. Based on the results, ZnAl2O4 2D nanosheets have been proven as an appropriate ARC material for increasing the PCE of PSSC.
Sachin Kumar, Naven Kumar, Kamna Yadav, Annveer and R.P. Singh
DFT analyses of electronic and optical spectra of barium cadmium chalcogenides (Ba2CdX3, X = S, Se, Te) have been carried out. The study of electronic spectra has been made in terms of band structure and density of states using full potential linear augmented plane wave plus local orbital method. Band structure calculations have been carried out under the approximations PBE-GGA, PBE-Sol, LDA and TB-mBJ. Band structures of these materials show that Ba2CdS3, Ba2CdSe3 and Ba2CdTe3 crystals possess a band gap less than 1 eV, underestimated relative to the experimental/theoretical literature values. Optical spectra of these chalcogenides have been analyzed in terms of real and imaginary parts of dielectric function, reflectivity, refractive index, extinction coefficient, absorption coefficient, optical conductivity and electron energy loss. Optical results show large anisotropy along different directions. These results provide a physical basis of barium cadmium chalcogenides for potential application in optoelectronic devices.
This is a study of a medical injection factory-Babylon carried out in order to achieve proper mechanical and morphological properties, PP has been injection molded by using cold runner injection molding machine with temperature variation (198, 200, 203……220°C) for ten samples. The physical and mechanical properties of PP product were examined. It has been found that the Shore hardness decreases linearly with injection molding temperature increasing. The tensile strength has a similar behavior to the hardness. However, it has been found that the MIF (Melt Index Flow) rates increases with the increase of injection molding temperature. The density of PP has been found for both virgin PP and the samples, it has been found that the density decreases with increasing operation temperature. FTIR (Fourier Transmission Infrared) spectra were taken for both samples with high and low operation temperature. Besides the SEM (Scanning Electronic Microscopy) test shows the difference in the morphology of the product surface and the PP product at high and low operation temperature. Moreover, for all these properties, the PP product exhibits good mechanical properties (hardness, tensile strength, density) for the samples produced at temperature lower than 207°C. While the physical properties such as MIF improved with injection temperature increasing, additionally, the SEM images show that the sample produced in low temperature have surface damage.
Setia Budi, Sukro Muhab, Agung Purwanto, Budhy Kurniawan and Azwar Manaf
The effect of electrodeposition potential on the magnetic properties of the FeCoNi films has been reported in this paper. The FeCoNi electrodeposition was carried out from sulfate solution using potentiostatic technique. The obtained FeCoNi films were characterized by X-ray diffractometer (XRD), atomic absorption spectrometer (AAS) and vibrating sample magnetometer (VSM). It has been shown that the electrodeposition potential applied during the synthesis process determines the magnetic characteristics of FeCoNi films. The more negative potential is applied, the higher Ni content is in the FeCoNi alloy. At the same time, Co and Fe showed almost similar trend in which the content decreased with an increase in applied potential. The mean crystallite size of FeCoNi films was ranging from 11 nm to 15 nm. VSM evaluation indicated that the FeCoNi film is a ferromagnetic alloy with magnetic anisotropy. The high saturation magnetization of FeCoNi film was ranging from 86 A·m2/kg to 105 A·m2/kg. The film is a soft magnetic material which was revealed by a very low coercivity value in the range of 1.3 kA/m to 3.7 kA/m. Both the saturation magnetization and coercivity values decreased at a more negative electrodeposition potential.
Katarína Stachová, Zdenko Stacho, Zuzana Papulová and Marek Jemala
The need for adaptation to rapid changes in the business environment, both on the part of employees and employers, implies dealing with new challenges, acquisition of new knowledge and skills and assumption of new roles and responsibilities. The base for companies is the availability of qualified human resources, which is ensured by the human resource management department mainly through an effective process of employee selection. The paper is oriented at the analysis of the current state of focus of organizations operating in Slovakia on systematicity and complexity of the selection process, the existence of an effective internal labor market and the regularity of development of used selection tools in the context of technological progress and changes in labor market requirements in regions of Slovakia. Results of the survey on (n = 343) enterprises show a positive trend, an increase of more than 10 percent in the orientation towards improvement of the process of employee selection, but on the other side it also confirm an increase in disparities between individual regions of Slovakia, some regions (Eastern Slovakia) progress much slower than the developed ones (Bratislava).
Fucheng Yu, Hailong Hu, Bolong Wang, Haishan Li, Tianyun Song, Boyu Xu, Ling He, Shu Wang and Hongyan Duan
Al doped ZnO (AZO) thin films were prepared on silica substrates by sol-gel method. The films showed a hexagonal wurtzite structure with a preferred orientation along c-axis. Suitable Al doping dramatically improved the crystal quality compared to the undoped ZnO films. Dependent on the Al dopant concentration, the diffraction peak of (0 0 2) plane in XRD spectra showed at first right-shifting and then left-shifting, which was attributed to the change in defect concentration induced by the Al dopant. Photocatalytic properties of the AZO film were characterized by degradation of methyl orange (MO) under simulated solar light. The transmittance of the films was enhanced by the Al doping, and the maximum transmittance of 80 % in the visible region was observed in the sample with Al concentration of 1.5 at.% (mole fraction). The film with 1.5 at.% Al doping achieved also maximum photocatalytic activity of 68.6 % under solar light. The changes in the film parameters can be attributed to the variation in defect concentration induced by different Al doping content.
The article presents the results regarding the elimination of constraints in the production process of a power equipment subassembly, a boiler chamber, together with an analysis of the benefits resulting from this, both financial and non-financial. The significance of bottlenecks in the production process, ways of its identification and limitations - in general - are presented. The article is a case-study of an attempt to eliminate the bottleneck in the production process of the boiler chamber, which turned out to be the process of drilling and marking-off, and work stations representing these processes. In order to eliminate the limitation, it was decided to replace the existing tracing and drilling work with a numerically controlled device - a boring machine moved from the liquidated department.. As a result, labor-intensive, manual chambers marking-off and the process of drilling holes with a smaller diameter drill have been eliminated. A number of benefits has been demonstrated resulting from the elimination of the bottleneck in the process, first of all, it was possible to reduce the duration of the marking-off and drilling operations and reduce the costs of the boiler chamber production process.
Tahmineh Jalali, Abdolrasoul Gharaati and Mohammad Rastegar
In this paper, employing of one-dimensional magnetophotonic crystals in infrared wavelengths range is considered. For this purpose, magnetophotonic multilayer structures, composed of magnetic defect layer surrounded by dielectric and MO Bragg mirrors, have been proposed. Ce:YIG with an optical thickness in the range of 0 to λs was used as a magnetic material. By using four by four transfer matrix method, the transmittance values and Faraday rotation (FR) angles of these structures were computed. The electric field distribution was obtained by Finite Element Method (FEM). By investigation of transmittance and FR angle of magnetophotonic crystals, it was possible to design the optimized structures with a rotation larger than 30 degrees and high transmittance. Such structures with a few micrometer thickness and fast magneto-optical (MO) responses have the potential to be used in MO devices like integrated photonic elements and sensors.
Nanostructures of copper (II) oxide were synthesized through chemical reduction of copper (II) sulfate pentahydrate using phytochemicals present in leaf extracts of Leucas aspera. The crystalline phases and size were assessed by X-ray diffraction data analysis. From the Bragg reflection peaks, existence of monoclinic end-centered phase of copper (II) oxide along with presence of cubic primitive phase of copper (I) oxide and traces of cubic face centered lattices of zero valent copper was revealed. The three Raman active modes corresponding to CuO phase were identified in the sample with permissible merging of characteristic bands due to nanostructuring and organic capping. The surface topography measurement using field emission scanning electron microscope evidenced the occurrence of cylindrical rod shaped morphological structures along with a number of unshaped aggregates in the sample. The effective crystallite size and lattice strain were estimated from Williamson-Hall analysis of Bragg reflection data. Tauc plot analysis of UV-Vis-NIR absorption data in direct transition mode provided an estimation of band gap, viz. 1.83 eV and 2.06 eV respectively, for copper (II) oxide and copper (I) oxide. Thermal degradation study using thermogravimetric curve analysis could reveal the amount of moisture content, volatile components as well as the polymer capping over nanorods present in the sample. It could be seen that upon heating, inorganic core crystals undergo oxidation process and at temperature above 464 °C, the sample was found to be composed solely of inorganic crystallite phase of copper (II) oxide.