The article describes 10 known programmes of practical flight training in military aviation – specialization: Multi-Mission Tactical Jet Pilot, which is the highest level of military pilot training in all types of military and civil aviation – comparable only to the level of training and experience of the pilot-instructor of the Military Aviation School. The presented comparison was developed on the basis of literature research from the point of view of, among others, an aircraft operation engineer and a pilot-instructor.
The paper presents application of Particle Image Velocimetry for determination of an airfoil’s drag coefficient in wind tunnel tests. The purpose of the study was to investigate the feasibility of using PIV as an alternative to pressure rake measurements, especially at high angles of attack. The integral momentum concept was applied for determination of fluid drag from experimental low speed wind tunnel data. The drag coefficient was calculated from velocity and pressure rake data for intermediate angles of attack from 5° to 10°. Additionally, the experimental results were compared to panel method results. After validating the procedures at low angles of attack, the drag coefficient was calculated at close to critical angles of attack. The presented study proved that PIV technique can be considered as an attractive alternative for drag coefficient determination of an airfoil.
Carbon-epoxy composite materials, due to their high strength in relation to mass, are increasingly used in the construction of aircraft structures, however, they are susceptible to a number of damages. One of the most common is delamination, which is a serious problem in the context of safe operation of such structures. As part of the TEBUK project, the Institute of Aviation has developed a methodology for forecasting the propagation of delamination. In order to validate the proposed method, an aerial structure demonstrator, modelled on the horizontal stabilizer of the I-23 Manager aircraft, was carried out. However, in order to carry out the validation, it was necessary to "simplify" the demonstrator model. The paper presents a numerical analysis conducted in order to separate from the TEBUK demonstrator model a fragment of the structure, which was used to study the delamination area, as an equivalent of the whole demonstrator. Subcomponent selection was carried out in several stages, narrowing down the analysed area covering delamination in subsequent steps and verifying the compliance of specific parameters with the same parameters obtained in a full demonstrator model. The parameters compared were: energy release rate values on the delamination front line and strain values in the delamination area. The numerical analyses presented in the paper were performed with the use of the MSC.Marc/Mentat calculation package. As a result of the analyses, a fragment of the structure was selected, which allows to significantly reduce the time and labour consumption of the production of the studied object, as well as to facilitate experimental research.
Stratospheric balloons are very important sources for space and terrestrial observation experiments in many disciplines. Instruments developed for astrophysical measurements are usually reusable. It is also possible to observe both hemispheres including observations from the polar and equatorial regions for thirty days or even longer. On the other hand the UV atmospheric transmittance window was used for the astrophysical observations less often than visible optical bands. At the end of the 2017 there are a few scientific groups working on near-UV or UV spectrographs and cameras for balloon flights.
In this paper we are discussing the possibility of ultraviolet measurement of Enceladus, an icy Saturnian moon, surface reflectance between 200 and 400 nm from the 20-50 km altitudes. At visible and near infrared optical channels Enceladus’ reflectance is very high (near 1.0). This value is consistent with a surface composed of water ice, however at some ultraviolet wavelengths Enceladus reflectance is lower than it would be expected for this type of surface. The scientific research done in the last decade was focused on H2O, NH3, and tholin particles detection on the Enceladus’ surface as a reason of low UV reflectance phenomenon. Continuous observation of Enceladus’ UV reflectance variability from stratospheric balloons may be interesting and may give us the proof of the presence of biomarkers or/and tholin particles.
European Commision adopted in July new regulations about laying down airspace usage requirements and operating procedures concerning performance based navigation. It is next step in realization of the the global program PBN ICAO. At the 36th General Assembly of ICAO held in 2007, the Republic of Poland agreed to ICAO resolution A36-23 which urges all States to implement PBN. In future aviation concepts the use of Performance Based Navigation (PBN) is considered to be a major Air Traffic Management (ATM) concept element. ICAO has drafted standards and implementation guidance for PBN in the ICAO Doc 9613 “PBN Manual”. The Based Performance Navigation Concept represents and shift from sensor-based to performance based navigation connected with criteria for navigation: accuracy, integrity, availability, continuity and functionality depending on the phase of the flight. Through PBN and changes in the communication, surveillance and ATM domain, many advanced navigation applications are possible to improve airspace efficiency, improve airport sustainability, reduce the environmental impact of air transport in terms of noise and emission, increase safety and improve flight efficiency.
The paper concentrates on post-processing of data necessary for pressure measurements using Pressure Sensitive Paints (PSP). The purpose of the study was to develop and test procedures for extraction of the surface pressure distribution from the images captured during PSP tests. The core issues addressed were reduction of the influence of model movement and deformation during wind tunnel run and synchronization between conventional pressure tap measurements and PSP data, necessary for in-situ calibration. In the course of the studies, two approaches on image registration were proposed: the first based on geometric transformation of control points pairs with cross-correlation tuning and the second based on similarity finding and estimation of geometric transformation of the images. Performance of the developed algorithm was tested with use of experimental set-up allowing for controlled movement of the imagined target with micrometer resolution. Both of the proposed approaches to PSP image resection proved to perform well. After testing of the software, the PSP system was used for determination of the pressure field on flat plate exposed to impinging jet. The presented procedures and results can be useful for research groups developing in-house PSP measurements systems for wind tunnel tests and internal flow investigations.
The article aims to present the results of analysis and evaluation of using energy clusters as a bulk electricity storage. There were developed an analytical model of a sample microgrid (on-grid) and analysed using a software dedicated for optimizing such microgrids. The model of microgrid consist on electricity commercial and residential loads, photovoltaic and wind installations and batteries.
This paper describes the recent theoretical and experimental research by the Netherlands Organisation for Applied Scientific Research (TNO) into green replacements for hydrazine, hydrazine derivatives and nitrogen tetroxide, as propellants for in-space propulsion. The goal of the study was to identify propellants that are capable of outperforming the current propellants for space propulsion and are significantly less hazardous for humans and the environment. Two types of propellants were investigated, being monopropellants and bipropellants. The first section of the paper discusses the propellant selection. Nitromethane was found to be the most promising monopropellant. As bipropellant, a combination of hydrogen peroxide (HP) and ethanol was selected, where the ethanol is rendered hypergolic with hydrogen peroxide. The second part of the paper describes the experimental verification of these propellants by means of engine testing. Initiation of the decomposition of nitromethane was found to be problematic, hypergolic ignition of the hydrogen peroxide and ethanol bipropellant however was successfully demonstrated.
Łukasz Jeziorek, Krzysztof Szafran and Paweł Skalski
The paper presents practical aspects of determining the amount of heat flow by measuring the distribution of surface temperature using the Temperature Sensitive Paint (TSP) method. The quantity measured directly with TSP is the intensity of the excited radiation, which is then converted to surface temperature. The article briefly presents three different methods for determining the heat transfer coefficient. Each of these methods is based on a separate set of assumptions and significantly influences the construction of the measuring station. The advantages of each of the presented methods are their individual properties, allowing to improve accuracy, reduce the cost of testing or the possibility of using them in tests of highly complex objects. For each method a mathematical model used to calculate the heat transfer coefficient is presented. For the steady state heat transfer test method that uses a heater of constant and known thermal power, examples of the results of our own research are presented, together with a comparison of the results with available data and a discussion of the accuracy of the results obtained.
Lyubomyr Sabadosh, Serhii Larkov, Oleg Kravchenko and Vladyslav Sereda
Numerous attempts have been undertaken to develop propulsion systems for nano-satellite-type spacecrafts to enable their maneuvering in orbits. One of the potentially viable chemical propellant propulsion systems is a hybrid system. The present paper studies propellant composition variants with the metal hydride as fuel that can be chosen for a nano-satellite hybrid propulsion system. It defines key requirements for chemical propellant nano-satellite propulsion systems, and specifies potential propellant pairs based on a compact metal hydride. The study describes basic technical characteristics of a 1U CubeSat propulsion system.