Waste material such as used tires is increasing every year, which poses environmental problems. However, such material has been used in several geotechnical applications as alternative lightweight backfill in highway embankments and/or behind retaining walls, providing environmental, economic and technical benefits. These applications require knowledge of engineering properties of soil-tire rubber mixtures. The present study aims to show the possibility of tire rubber usage in sand by evaluating the shear strength and deformability of sand mixed with granulated rubber, in weight percentages between 0 and 50%. The tire rubber content was found to influence the stress-strain and deformation behavior of the mixtures. The shear strength of sand mixed with 10% or 20% tire rubber was higher than that measured for sand only. However, the trend for TRC = 30–50% was different. Samples with a rubber content of 30-50% exhibited a rapid decrease in the stress ratio compared with that of sand. The major principal strain at maximum stress ratio was found to increase with increasing tire rubber content. However, it was observed that the lateral strains (minor and intermediate principal strains) of samples reduced significantly with the addition of tire rubber to the sand.
At present, the suspended monorail systems constitute a very common means of transportation in the Polish hard coal mines. The main advantages of the suspended monorail include the independence of the route from the working floor surface irregularities and the possibility to transport cargo of significant mass and size.
The masses and dimensions of machines and devices transported via monorail have increased considerably in recent times. This particularly concerns the transport of longwall system elements. In Poland, the maximum speed of suspended monorail travel is 2 m/s. Due to the fact that preparations are currently underway to increase the maximum speed above 2 m/s, it is necessary to inspect what influence it will have on work safety and mining support stability.
Current operational experience and tests have shown that dynamic loads induced by the suspended monorail transportation have a significant influence on the roadway support stability, working protection durability and on the monorail operators. This is particularly true during the emergency braking of a suspended monorail by means of a braking trolley, where the overloads reach 3g.
Bench tests of the selected steel arch and rock bolt support elements utilised in the Polish hard coal mines were conducted in order to determine the resistance of steel arch and rock bolt supports to static and dynamic loads.
The article presents the results of the tests conducted on a steel arch support in the form of the sliding joints of an ŁP/V29 yielding roadway support, which is commonly employed in the Polish hard coal mines. Tests of elements of the threaded bolts with trapezoidal threads over the entire rod length were conducted as well.
The conducted strength tests of steel arch and rock bolt support elements under static and dynamic loading have shown that dynamic loading has decisive influence on the support’s retaining of its stability. Support element stability decreases along with the increase of the impact velocity. This concerns both the steel arch support and the rock bolt support.
In this publication a Doctrine for the Conditional Extremization of the Hybrid-Optional Effectiveness Functions Entropy is discussed as a tool for the Reliability Assessments of Engineering Systems. Traditionally, most of the problems having been dealt with in this area relate with the probabilistic problem settings. Regularly, the optimal solutions are obtained through the probability extremizations. It is shown a possibility of the optimal solutions “derivation”, with the help of a model implementing a variational principle which takes into account objectively existing parameters and components of the Markovian process. The presence of an extremum of the objective state probability is observed and determined on the basis of the proposed Doctrine with taking into account the measure of uncertainty of the hybrid-optional effectiveness functions in the view of their entropy. Such approach resembles the well known Jaynes’ Entropy Maximum Principle from theoretical statistical physics adopted in subjective analysis of active systems as the subjective entropy maximum principle postulating the subjective entropy conditional optimization. The developed herewith Doctrine implies objective characteristics of the process rather than subjective individual’s preferences or choices, as well as the states probabilities maximums are being found without solving a system of ordinary linear differential equations of the first order by Erlang corresponding to the graph of the process. Conducted numerical simulation for the proposed mathematical models is illustrated with the plotted diagrams.
As the rotor configuration has the most impact on helicopter properties, the process of determination the assumptions for rotor design is a very important factor in the early stage of rotorcraft development. The following paper presents a mechanical analysis process used at the Institute of Aviation to quickly develop a coaxial rotor prototype applicable in ultra-light unmanned helicopter which has the potential for further improvement of its flight parameters. The article describes the rotor analysis process due to its feasibility based on commercially available solutions, the process of formulating assumptions for the entire structure, MES analysis of the rotor parts all leading to creation of the rotor prototype.
Ruben Di Battista, Maria Teresa Scelzo and Maria Rosaria Vetrano
Slushes are two-phase solid-liquid single-species cryogenic fluids that exhibit an increased density and a greater heat capacity with respect to the corresponding normal boiling point liquids. These promising features are of large interest for applications that exploit slush as a thermal fluid, like super magnets refrigeration, cryogenic cooling of bio-materials or air conditioning, and for aerospace systems that use slush fluids as fuel or oxidizer. Several programs in the frame of the research on Slush Hydrogen (SLH2) as a new-generation fuel for aerospace propulsion have been started in the past. This work was carried out in the framework of a VKI research activity promoted by the Predict ESA Technology Research Programme, to investigate experimentally and numerically the behavior of slush flows in a representative upper stage feeding line. In this paper, we present a simulation based on a granular two-fluid model on an isothermal solid liquid mixture (slurry) and a Nitrogen slush (SLN2) fluid flowing in a horizontal pipe. A finite-volumes discretization using the software library OpenFOAM was benchmarked against experimental and numerical literature data, to assess the accuracy of the code in predicting pressure drops along the pipe axis and solid particle distribution across the pipe diameter. Moreover, the effects of concentration and inlet velocity are investigated. We show that the numerical model fairly reproduces the literature data in terms of important aspects as the solid volume fraction distribution and the pressure drops, especially for high flow rates.
This article presents adhesive shearing test methods, focusing especially on the ASTM D5656 method. These methods will be briefly characterized and compared. The most important concerns about the D5656 method are described. With the use of ASTM D1002 and D5656 methods, the influence of adherend surface preparation on shearing properties of the bond is evaluated. Compared to sandblasting only, sandblasting followed by the FPL process (sulfochromate etching of aluminum) increased shear strength of joints by 35 % for ASTM D1002 tests and by 48% for D5656 tests. Comparing these two methods, shear strength obtained in D5656 tests is about two times higher than in D1002 tests. The cause for this phenomena is much larger adherend thickness in the D5656 method, which provides the coupons with increased stiffness. Shear modulus, calculated with 3 different calculation methods, showed differences in obtained results, which points to necessary actualization of D5656 standard.
Publication contains a description of the preparation and the implementation of a test flight of a stratospheric balloon with a mounted camera GoPro Hero3. Description includes: used equipment, its parameters, role in the success of the mission and the difficulties and limitations that the project team encountered during the preparation and implementation of the flight. The mission was attended by a team of six engineers and scientists from the Remote Sensing Division, who were also involved in the implementation of the HESOFF project. One of the main goals of the HESOFF project was to obtain aerial images on the Krotoszyńska Plate (woj. wielkopolskie) using the Unmanned Aerial Vehicle (UAV) and to carry out remote monitoring of oak stands. The primary goal of an experimental balloon flight was to check the technical operational capability and gain experience in planning and implementing this type of project. During the balloon raising, the video material was acquired in the form of a recording, which later was analyzed. On the basis of the collected information, the conclusions regarding the possibility of implementing a long endurance flight in the stratosphere, illustrating (using a multisensor platform) research surfaces of the HESOFF project were presented. The stages of implementation of the presented mission were divided into following parts: preparation of the flight with the completion of equipment and necessary documents (flight permission), proper flight realization, understood as the release of the balloon and identification of the place where the equipment landed, as well as analysis and presentation of the results.
This paper is a review of testing methods dedicated for sandwich type composite structures with honeycomb core. First, information about the composition of sandwich materials structures, their properties, types of core materials and applications in the industry is presented. Mechanical properties were compared in the case of different types of the core material. Later, tests methods needed to describe properties of those materials and normalization organizations which create them were mentioned. The testing methods were divided into two groups: mechanical and physicochemical tests. Mechanical properties are: compressive strength (two types of test), edge compressive strength, shear strength (in two directions) and tension strength (two types of test). Physicochemical properties are: material density, water migration, water absorption and thermal conductivity. Testing methods were described according to American Society for Testing and Materials (ASTM) standards. This article is based on professional literature and the author’s experience.
The paper presents simulation method and results of calculations determining behavior of helicopter and landing site loads which are generated during phase of the helicopter take-off and landing. For helicopter with whirling rotor standing on ground or touching it, the loads of landing gear depend on the parameters of helicopter movement, occurrence of wind gusts and control of pitch angle of the rotor blades. The considered model of helicopter consists of the fuselage and main transmission treated as rigid bodies connected with elastic elements. The fuselage is supported by landing gear modeled by units of spring and damping elements. The rotor blades are modeled as elastic axes with sets of lumped masses of blade segments distributed along them. The Runge-Kutta method was used to solve the equations of motion of the helicopter model. According to the Galerkin method, it was assumed that the parameters of the elastic blade motion can be treated as a combination of its bending and torsion eigen modes. For calculations, data of a hypothetical light helicopter were applied. Simulation results were presented for the cases of landing helicopter touching ground with different vertical speed and for phase of take-off including influence of rotor speed changes, wind gust and control of blade pitch. The simulation method may help to define the limits of helicopter safe operation on the landing surfaces.
M. Davarpanah, G. Somodi, L. Kovács and B. Vásárhelyi
Understanding the quality of intact rock is one of the most important parts of any engineering projects in the field of rock mechanics. The expression of correlations between the engineering properties of intact rock has always been the scope of experimental research, driven by the need to depict the actual behaviour of rock and to calculate most accurately the design parameters. To determine the behaviour of intact rock, the value of important mechanical parameters such as Young’s modulus (E), Poisson’s ratio (ν) and the strength of rock (σcd) was calculated. Recently, for modelling the behaviour of intact rock, the crack initiation stress (σci) is another important parameter, together with the strain (σ). The ratio of Young’s modulus and the strength of rock is the modulus ratio (MR), which can be used for calculations. These parameters are extensively used in rock engineering when the deformation of different structural elements of underground storage, caverns, tunnels or mining opening must be computed. The objective of this paper is to investigate the relationship between these parameters for Hungarian granitic rock samples. To achieve this goal, the modulus ratio (MR = E/σc) of 50 granitic rocks collected from Bátaapáti radioactive waste repository was examined. Fifty high-precision uniaxial compressive tests were conducted on strong (σc >100 MPa) rock samples, exhibiting the wide range of elastic modulus (E = 57.425–88.937 GPa), uniaxial compressive strength (σc = 133.34–213.04 MPa) and Poisson’s ratio (ν = 0.18–0.32). The observed value (MR = 326–597) and mean value of MR = 439.4 are compared with the results of similar previous researches. Moreover, the statistical analysis for all studied rocks was performed and the relationshipbetween MR and other mechanical parameters such as maximum axial strain for studied rocks was discussed.