A photocode in Polish is a common name for a two-dimensional code, which is characterized by higher information capacity than a traditional barcode. The paper analyses the use of the two-dimensional coding system - DataMatrix to identify and classify the material stream in the production process. The analysis showed the effectiveness of the implementation of the coding system in the context of increased availability, machine use and increased product quality. The improvement in the production process is confirmed by an increase in the OEE index. As part of further improvement measures, the coding system should be implemented throughout the enterprise, its compatibility with existing systems should be ensured and applied to all products.
This paper presents some aspects of the process of services, products and manufacturing transfer, with the associated production resources, from other locations and plants to Poland.
The study was carried out on the basis of an analysis of publications about delocalization as well as by means of desk research, where there were used the accessible primary and secondary data such as branch reports, statistical data available in reports, data bases, and information accessible on Polish and European websites. The article is also the result of the author's experience of participation in the relocation of a number of international companies, regarding various industries. Delocalization in Poland was presented both from the point of view of Conceptualizing delocalization (literature review, theoretical position) and Implementation of production.
The delocalization mainly takes advantage of labor forces. On the other hand, it may also concern innovative activities and develop high-tech for regions affected by economic restructuring. The social policies for the risk mitigation of the delocalization of production are also being developed and implemented. This work clarifying the conditions of delocalization in Poland and highlight the important roles played by innovation and institutions for achieving sustainability.
In this paper, an outlook about the present of electrical aviation is given. The relatively small energy density of current battery technologies is adequate to build usable electric car, but not suitable for electric aircraft. Because of the very limited amount of energy available on-board, a couple of percent in efficiency can give significant increase in range and flight time, hence the development of more efficient propulsion system and E-motor is as important as the development of battery technologies. Current research results at the University of Dunaujvaros show, that building E-motors from amorphous materials is possible, and can easily increase the efficiency of high speed E-motors.
In this publication a Doctrine for the Conditional Extremization of the Hybrid-Optional Effectiveness Functions Entropy is discussed as a tool for the Reliability Assessments of Engineering Systems. Traditionally, most of the problems having been dealt with in this area relate with the probabilistic problem settings. Regularly, the optimal solutions are obtained through the probability extremizations. It is shown a possibility of the optimal solutions “derivation”, with the help of a model implementing a variational principle which takes into account objectively existing parameters and components of the Markovian process. The presence of an extremum of the objective state probability is observed and determined on the basis of the proposed Doctrine with taking into account the measure of uncertainty of the hybrid-optional effectiveness functions in the view of their entropy. Such approach resembles the well known Jaynes’ Entropy Maximum Principle from theoretical statistical physics adopted in subjective analysis of active systems as the subjective entropy maximum principle postulating the subjective entropy conditional optimization. The developed herewith Doctrine implies objective characteristics of the process rather than subjective individual’s preferences or choices, as well as the states probabilities maximums are being found without solving a system of ordinary linear differential equations of the first order by Erlang corresponding to the graph of the process. Conducted numerical simulation for the proposed mathematical models is illustrated with the plotted diagrams.
A short survey is reported on the advantageous and disadvantageous properties of soft magnetic glassy tapes to build stator and rotor elements for the increase of motor efficiency. The relative high saturation magnetization and the relative permeability of these alloy groups seem to be promising in this application field. On the other hand, the sample thickness (30 µm) displays limitations in terms of a filling factor. High hardness of tapes hinders the effectivity of mechanical shaping. Laser cutting can be successful as shaping method, presuming that the extension (thickness) of heat affected zone (HAZ) can be successfully reduced below 50µm, avoiding the brittleness evolution.
Eva Nedeliaková, Vladimíra Štefancová and Michal Petr Hranický
The provision of quality transport services is a prerequisite for the creation of an efficient organization that can meet the expectations and requirements of both the enterprise itself and its customers. From the railway enterprise's point of view, it is necessary to pay attention to the increasingly demanding requirements of its customers in railway passenger transport. This article focuses on identifying defects in rail transport processes that negatively affect ordinary operations. One of the most serious bottlenecks affecting railway transport reliability is the train delay, which fundamentally affects the perception of railway transport. At the same time, it emphasizes the need to apply individual tools according to the DMAIC cycle in order to achieve continuous improvement. The aim of the implemented Six Sigma methodology in railway enterprise is disciplined application of statistical problem-solving tools to recognize the gaps in the transport process and set out individual steps for their gradual removal.
As the rotor configuration has the most impact on helicopter properties, the process of determination the assumptions for rotor design is a very important factor in the early stage of rotorcraft development. The following paper presents a mechanical analysis process used at the Institute of Aviation to quickly develop a coaxial rotor prototype applicable in ultra-light unmanned helicopter which has the potential for further improvement of its flight parameters. The article describes the rotor analysis process due to its feasibility based on commercially available solutions, the process of formulating assumptions for the entire structure, MES analysis of the rotor parts all leading to creation of the rotor prototype.
The article is devoted to solving the fundamental and applied problem of nonlinear structural mechanics of machines by introducing into the drum two additional stop cylinders with supporting rollers at the end and adjustable length, providing a given elliptical or circular shape of a flexible shell with a smoothly variable geometry in the area of its contact with compacted pavement material. Compaction of soil, gravel and asphalt concrete in the sphere of road is not only an integral part of the technological process of the roadbed, road foundation and surface construction, but it is actually the main operation to ensure their strength, stability and durability. The quality, cost and speed of road construction, the possibility of using fundamentally new technologies, structures and materials is largely determined by the availability of modern road machinery.
Technology assessment (TA) is not a new concept. High value energy technology identification needs to be followed by a decision process in which all shareholders contribute. A case study on Combined and Heat Power (CHP) technologies considered is presented to illustrate the applicability of fuzzy analytical hierarchy assessment approach (FAHP). The goal of this paper is to identify and evaluate the best variant of CHP technologies using multi-criteria that are technical feasibly and cost effective reflecting performance parameters. The results depict that technology A2 with an overall ranking of 0.438 is the best alternative compared to others. Taking into consideration decision parameters for the section, A1 is found to be relatively most important with a rating of 0.434 with its reliability and cost effectiveness. The presented fuzzy-based methodology is general expected to be used by a diverse target groups in energy sectors.
Ruben Di Battista, Maria Teresa Scelzo and Maria Rosaria Vetrano
Slushes are two-phase solid-liquid single-species cryogenic fluids that exhibit an increased density and a greater heat capacity with respect to the corresponding normal boiling point liquids. These promising features are of large interest for applications that exploit slush as a thermal fluid, like super magnets refrigeration, cryogenic cooling of bio-materials or air conditioning, and for aerospace systems that use slush fluids as fuel or oxidizer. Several programs in the frame of the research on Slush Hydrogen (SLH2) as a new-generation fuel for aerospace propulsion have been started in the past. This work was carried out in the framework of a VKI research activity promoted by the Predict ESA Technology Research Programme, to investigate experimentally and numerically the behavior of slush flows in a representative upper stage feeding line. In this paper, we present a simulation based on a granular two-fluid model on an isothermal solid liquid mixture (slurry) and a Nitrogen slush (SLN2) fluid flowing in a horizontal pipe. A finite-volumes discretization using the software library OpenFOAM was benchmarked against experimental and numerical literature data, to assess the accuracy of the code in predicting pressure drops along the pipe axis and solid particle distribution across the pipe diameter. Moreover, the effects of concentration and inlet velocity are investigated. We show that the numerical model fairly reproduces the literature data in terms of important aspects as the solid volume fraction distribution and the pressure drops, especially for high flow rates.