Elena Lezhneva, Katerina Vakulenko and Andrii Galkin
The problem of combating urban noise is closely linked to the rational transformation of the urban environment, which must go through the elimination or reduction of the number of sources of noise, the localization of the noise emission zone, reducing the level of sound sources and protection against noise for the residential areas. Theoretical and experimental studies of acoustic loading on the territory along the highway for the typical section of the urban territory have been conducted. To estimate the complex noise impact from all sources and from individual sources, as well as to predict the total noise exposure for this site, a noise map was constructed using software. As a measure to combat traffic noise in the territory along the highway, the location of the noise protection screen was justified, taking into account the loss of part of the national income as a result of the continuous impact of noise on a person.The results of the research allow to assess the degree of technogenic impact of noise pollution during the operation of the highway, which allows regulating, by administrative and legislative methods, the nature of the impact on natural objects and human health of certain types of activities, as well as reasonably proposing measures that ensure environmental safety when organizing urban streets traffic.
Segment videos were produced at different peaks to reflect different sampling criteria like land use characteristics, trails, Ciclocarrils and Ciclovia. Each segment was filmed for 20–40 seconds during bicycle rides at a speed of about 5km/h with a camera strapped, at an angle of 45 degrees, on the head. Curb lane variables such as bicycle pathway widths, curb lane motorised volume (veh/h) and vehicle speed (km/h), bicycle volume on segment, and median width were recorded in addition to secondary data. About 1,360 ratings were acquired from study participants and used in the estimation process. Ordered probability models were used to estimate random parameters of cyclists LOS perception to account for unobserved heterogeneity for all respondents. The deviance (1.085) and Pearson Chi-Square (2.309) with 1,635 degree of freedom at 0.05 level of significance shows that our model provides a better fit of the data. The study observed that BLOS was strongly influenced by side path separation, vehicle speed, motorised traffic volume and conflicts with pedestrians. However, many other factors were found to have high probabilities to influence level of service with unit change. They include bicycle lane width, wide outside lane, pavement conditions, trees and benches, daylight, gender and experience of cyclist. The impact of the variety of observed factors affecting bicyclists reveal the nature and character of urban transportation in Bogota which suggests a range of important trade-offs in further planning and management of the Cicloruta bicycle paths.
Moisture-sensitive or collapsible soils are materials with high porosity that under the loads transmitted by the superstructure or even under its own weight present additional settlements once the soil is saturated. This category includes loess deposits and other high silt content soils with uneven porosity. A method often used for foundation on these soils is the realization of local loessoid material compacted columns. This paper presents, on one hand, the experimental laboratory programs aiming to achieve some optimal mixtures of local material (loess) and different other materials (sand, bentonite, cement) in order to improve the values of the mechanical parameters of the soil and so, to limit the settlements. On the other hand, it presents a lot of settlement calculations for different case scenarios.
Naima Ezzaki, Daniel Stoica, Laurentiu Rece and Arina Modrea
This article aims to highlight, through a comparative study, the efficiency of steel bracing systems used to reduce seismic vulnerabilities in existing buildings with reinforced concrete structures (reinforced concrete frames and reinforced concrete dual structures, general building structures including those used in transport infrastructure). In order to simplify the calculations, the analysis was reduced to the study of the behavior of resistance lines corresponding to four-, nine- and fifteen-level buildings with the same plane distribution. In order to obtain features similar to those of existing building elements, structures were initially loaded with seismic forces corresponding to code P13-63. The next step was to apply to previously dimensioned structures the seismic loads according to P100-3: 2008 in relation to P100-1: 2013, thus obtaining the deficiencies of the existing structures against the requirements of these norms. Correction of these strength and stiffness deficiencies was attempted by introducing X-shaped centric brace systems. The bracing systems used as consolidation methods are of three types: direct bracings stuck in the reinforced concrete frames and bracings of the indirect type, made of internal and external bracing steel frames. Structural calculations were made in the linear elastic field using the ETABS program.
Mihai Dicu, Andreea Matei and Constantin Dorinel Voiniţchi
The paper follows the potential practice of fiber reinforced concrete (FRC) as a solution for airport`s runway pavements, in order to increase the bearing strength, resulting in decreasing the height of the concrete layer that is currently used.
Experimentally, the study focuses on the properties of fiber reinforced Portland cement concrete using 3 different percentages (0.5%, 1% and 1.5% of the concrete volume) and 4 different types of fiber (for 1% percentage – hooked steel fiber 50 mm length, hooked steel fiber 30 mm length, crimped steel fiber 30 mm length and polypropylene fiber 50 mm lenght), using as reference a plain concrete with 5 MPa flexural strength.
More exactly, the study presents the change in compressive and flexural strength, shrinkage, thermal expansion factor, elastic modulus and Poisson`s ratio over fiber type and dosage.
For the highest performance concrete (7 MPa flexural strength), it has been made a study using two methods for rigid airport pavements design (general method and optimized method), and one method for evaluation of bearing strength (ACN – PCN method), which is compared to a plain 5 MPa concrete. Furthermore, the decrease in the slab`s thickness proportionally to the growth of the flexural strength is emphasized by evaluating the slab`s height for a high performance 9 MPa concrete using both design methods.
Laurentiu Rece, Naima Ezzaki, Daniel Stoica and Victor Florin Jeflea
The present article aims to point out, with the help of a comparative research, the efficiency of tuned mass dampers, modern variants of consolidation ensuring seismic structural safety, used for buildings with a reinforced concrete structure, designed and produced according to the new codes. Case studies were based on structural computations in the linear elastic field using the ETABS program.
Jasna Tolmac, Slavica Prvulovic, Marija Nedic and Dragisa Tolmac
The paper analyzes the development opportunities of solar systems in the Republic of Serbia. Renewable energy sources and their energy potential, such as solar energy, should be considered in order to meet the needs of consumers. Solar energy can be considered the most modern renewable energy whose utility is still developing, and it is not represented as the utilization of hydro energy sources. Researches show that Serbia is a country with a high RES potential and that it has favorable conditions for production of electrical and heat energy from renewable sources. The aim of this paper is to present the possibilities of using solar energy in Serbia. Energy supply from renewable energy sources is a key factor for each country's strategy, because it directly contributes to reducing the negative effect on the environment.
A photocode in Polish is a common name for a two-dimensional code, which is characterized by higher information capacity than a traditional barcode. The paper analyses the use of the two-dimensional coding system - DataMatrix to identify and classify the material stream in the production process. The analysis showed the effectiveness of the implementation of the coding system in the context of increased availability, machine use and increased product quality. The improvement in the production process is confirmed by an increase in the OEE index. As part of further improvement measures, the coding system should be implemented throughout the enterprise, its compatibility with existing systems should be ensured and applied to all products.
Stanisław Parafiniuk, Alaa Kamel Subr, Marek Milanowski and Anna Krawczuk
Three different types of nozzles (different wear rate) were used in this study. They are classified depending on the severity of their wear to three groups: new, worn and damaged nozzles. Those nozzles were spraying with the same application rate (303 l/ha) on two-year field trials; this was achieved by changing the spraying pressure for each group of nozzles in order to get the same application rate. This practice is usually done by operators of sprayers, who calibrate the sprayers on the same application rate every year without changing the nozzles, so they tend to reduce the spraying pressure in order to compensate the flow rate increase due to the nozzles yearly wear. Two types of plant growth regulators (PGR) agents were used in this study, namely: Moddus and Kelpak, they were applied to wheat plants field to reduce lodging. The results showed that applying PGR in the year 2015 produced an increase in the wheat yield and reduction in the plant height regardless the nozzle type, although there was not any occurrence of wheat lodging. In the year 2016, the new nozzles produced higher values of wheat yield than other two types of nozzles.
This paper presents some aspects of the process of services, products and manufacturing transfer, with the associated production resources, from other locations and plants to Poland.
The study was carried out on the basis of an analysis of publications about delocalization as well as by means of desk research, where there were used the accessible primary and secondary data such as branch reports, statistical data available in reports, data bases, and information accessible on Polish and European websites. The article is also the result of the author's experience of participation in the relocation of a number of international companies, regarding various industries. Delocalization in Poland was presented both from the point of view of Conceptualizing delocalization (literature review, theoretical position) and Implementation of production.
The delocalization mainly takes advantage of labor forces. On the other hand, it may also concern innovative activities and develop high-tech for regions affected by economic restructuring. The social policies for the risk mitigation of the delocalization of production are also being developed and implemented. This work clarifying the conditions of delocalization in Poland and highlight the important roles played by innovation and institutions for achieving sustainability.