Browse

11 - 20 of 122 items :

  • Engineering x
  • Materials Sciences x
  • Business and Economics x
  • Process Engineering and Industrial Engineering x
Clear All

Abstract

Additive manufacturing has recently expanded its potential with the development of selective laser melting (SLM) of metallic powders. This study investigates the relation between the mechanical properties and the microstructure of Ti6Al4V alloy produced by SLM followed by a hot isostatic pressing (HIP) treatment. HIP treatment minimizes the detrimental influence of material defects. Tensile specimens produced with reference to specific building axes were prepared using a Renishaw A250 system. It has been found that the tensile strength and elongation depend on specimen building direction. Microstructural and textural characterizations were carried out to identify the source of differences.

Abstract

The windshield defrost system, in general, is a vehicle safety feature. Thus, its restricted by variety of directives. However, the OMEs’ benchmark targets could be even more demanding as the deicing process is in addition also part of passengers comfort. From vehicle design point of view the wind-shield defrost system is typically connected to HVAC unit (Heating, Ventilation and Air Conditioning). In the technical solution the windshield is heated via hot air convection. Nevertheless, other methods are becoming more and more popular, like directly heated glass by hot wire ohmic heating (heated glasses). The defrost CFD model should predict the ice layer thickness in time and space and in environmental conditions defined according to appropriate directives and technical solution. The accurate and fast modelling technique is essential part of a vehicle development, especially nowadays, where the optimization techniques area widely used and requires hundreds of simulations runs. Modelling requests are even increasing with modern pure electric vehicles (EVs), were the thermal and energy management is more demanding compared to the classical internal combustion engine (ICE) vehicles. The aim of the work is to verify possibility to model the ice layer thickness with simplified approach, which could be beneficial from computational time burden.

Abstract

The sieves’ manufacturers that want to be competitive at the market must have the implemented quality control system. Different methods, based on taking the sample, which is a representative of the total quantity of the forming sieves production, are applied for evaluation of the sieve’s conformity. The basic characteristics of this type of the quality function are control, measuring and testing of the forming sieves’ properties at the end of the manufacturing process. The objective is to detect and separate the products that deviate from the set criteria, to remain in the factory, then to be repaired if possible or discarded in the opposite case and thus to prevent delivery of the defective sieves to the paper manufacturers.

Abstract

This is a study of a medical injection factory-Babylon carried out in order to achieve proper mechanical and morphological properties, PP has been injection molded by using cold runner injection molding machine with temperature variation (198, 200, 203……220°C) for ten samples. The physical and mechanical properties of PP product were examined. It has been found that the Shore hardness decreases linearly with injection molding temperature increasing. The tensile strength has a similar behavior to the hardness. However, it has been found that the MIF (Melt Index Flow) rates increases with the increase of injection molding temperature. The density of PP has been found for both virgin PP and the samples, it has been found that the density decreases with increasing operation temperature. FTIR (Fourier Transmission Infrared) spectra were taken for both samples with high and low operation temperature. Besides the SEM (Scanning Electronic Microscopy) test shows the difference in the morphology of the product surface and the PP product at high and low operation temperature. Moreover, for all these properties, the PP product exhibits good mechanical properties (hardness, tensile strength, density) for the samples produced at temperature lower than 207°C. While the physical properties such as MIF improved with injection temperature increasing, additionally, the SEM images show that the sample produced in low temperature have surface damage.

Abstract

The need for adaptation to rapid changes in the business environment, both on the part of employees and employers, implies dealing with new challenges, acquisition of new knowledge and skills and assumption of new roles and responsibilities. The base for companies is the availability of qualified human resources, which is ensured by the human resource management department mainly through an effective process of employee selection. The paper is oriented at the analysis of the current state of focus of organizations operating in Slovakia on systematicity and complexity of the selection process, the existence of an effective internal labor market and the regularity of development of used selection tools in the context of technological progress and changes in labor market requirements in regions of Slovakia. Results of the survey on (n = 343) enterprises show a positive trend, an increase of more than 10 percent in the orientation towards improvement of the process of employee selection, but on the other side it also confirm an increase in disparities between individual regions of Slovakia, some regions (Eastern Slovakia) progress much slower than the developed ones (Bratislava).

Abstract

The article presents the results regarding the elimination of constraints in the production process of a power equipment subassembly, a boiler chamber, together with an analysis of the benefits resulting from this, both financial and non-financial. The significance of bottlenecks in the production process, ways of its identification and limitations - in general - are presented. The article is a case-study of an attempt to eliminate the bottleneck in the production process of the boiler chamber, which turned out to be the process of drilling and marking-off, and work stations representing these processes. In order to eliminate the limitation, it was decided to replace the existing tracing and drilling work with a numerically controlled device - a boring machine moved from the liquidated department.. As a result, labor-intensive, manual chambers marking-off and the process of drilling holes with a smaller diameter drill have been eliminated. A number of benefits has been demonstrated resulting from the elimination of the bottleneck in the process, first of all, it was possible to reduce the duration of the marking-off and drilling operations and reduce the costs of the boiler chamber production process.

Abstract

The National Quality Programme of the Slovak Republic for 2017-2021 strongly emphasises the primary objectives and priorities of the Quality Improvement Strategy. This should be one of the main priorities of the Slovak Government in the upcoming period. The Quality Improvement Strategy should, in general, lead to an improvement in the quality of life. The aim of the paper is to point out the opportunities for improvement by applying indicators aimed at defining the excellence of organisations within the national economy of the Slovak Republic.

Abstract

The construction industry in India is the second most important contributor to its gross domestic product. However, high rate of accidents and fatalities have tarnished the image of industry in India. Although the industry contributes significantly to the Indian economy, safety management is the primary concern alongside with frequent workplace accidents. The role of safety management is vital to improve safety performance of an organization. The functions of safety management include planning, organizing, staffing, directing, controlling and coordinating safety activities with an aim to minimize accidents/injuries. Safety trainings, employee participation, compliance of safety procedures and motivational schemes are part of safety management which influences the overall safety performance. Several metrics were developed to measure the safety performance of an organization but not a single measure will reflect the overall performance. The present study considered parameters pertaining to the safety management which have influence on the safety performance of a construction organization in India. The parameters are analyzed by formulating a goal programming model. The results of the study suggests that much improvement is needed in the area of safety trainings and the revised targets were established.

Abstract

Presented paper concentrate on problems connected with the role of operation manager within industrial company. Operation management concentrate many activities in today’s industrial corporation and because of that the role of it’s manager is very important. He should to have many skills described in this paper. We analysed responsibilities of the operation manager, his basic operational skills and also give some examples of duties and responsibilities of good operation manager on the example of food industry. This example can give some remarks about practical skills needed in operation management in particular enterprise.

Abstract

The paper concentrates on the issues of applying smart technologies in the manufacturing processes. The author includes in it brief descriptions of the smart technologies that contributed to the emergence of Industry 4.0 concept. Additionally, based on reports and surveys conducted on a global scale regarding the application of intelligent technologies, the author analyses the current state of implementing these technologies in manufacturing processes and provides forecasts regarding the adoption of the solutions based on Artificial Intelligence in global enterprises in the near future.