Single crystals of pure and L-threonine added tartaric acid (LT/TA), organic nonlinear optical (NLO) materials were grown from their respective aqueous solution by slow evaporation method. The crystalline nature of the grown crystals was confirmed by powder X-ray diffraction analysis (XRD). UV-Vis-NIR absorption and transmission spectra revealed that the lower cut-off wavelength was around 281 nm and the crystals exhibited high transmission over visible and near IR region. The presence of the functional groups such as O–H, C–H, C–O, C=O in the grown crystals was confirmed by FT-IR analysis. CHN analysis was carried out to confirm the presence of L-threonine in the grown crystals. Microhardness study on the crystals revealed that the hardness number Hv increased with the applied load. The growth pattern of the crystals were analyzed through etching analysis from which the etch patterns in the shape of ‘step-triangle’ were observed. The second harmonic generation (SHG) properties of pure and L-threonine doped tartaric acid crystals were confirmed by Kurtz-Perry powder technique.
Artur Wiatrowski, Michał Mazur, Agata Obstarczyk, Danuta Kaczmarek, Roman Pastuszek, Damian Wojcieszak, Marcin Grobelny and Małgorzata Kalisz
In this paper, comparative studies on the structural, surface, optical, mechanical and corrosion properties of titanium dioxide (TiO2) thin films deposited by continuous and sequential magnetron sputtering processes were presented. In case of continuous process, magnetron was continuously supplied with voltage for 90 min. In turn, in sequential process, the voltage was supplied for 1 s alternately with 1 s break, therefore, the total time of the process was extended to 180 min. The TiO2 thin films were crack free, exhibited good adherence to the substrate and the surface morphology was homogeneous. Structural analysis showed that there were no major differences in the microstructure between coatings deposited in continuous and sequential processes. Both films exhibited nanocrystalline anatase structure with crystallite sizes of ca. 21 nm. Deposited coatings had high transparency in the visible wavelength range. Significant differences were observed in porosity (lower for sequential process), scratch resistance (better for sequential process), mechanical performance, i.e. hardness:elastic modulus ratio (higher for sequential process) and corrosion resistance (better for sequential process).
G.W. Strzelecki, K. Nowakowska-Langier, R. Chodun, S. Okrasa, B. Wicher and K. Zdunek
The research on the influence of modulation frequency on the properties of films synthesized using a unique pulsed power supply combined with a standard unbalanced circular magnetron was conducted in the process of pulsed magnetron sputtering (PMS). It was shown that by using different levels of modulation, the composition of plasma (measured by optical emission spectroscopy, OES) as well as film growth rate and morphology (observed with scanning electron microscope, SEM), can be changed. The impact of modulation is related to the used materials and gases and can vary significantly. It was concluded that modulation frequency can greatly influence the synthesis of materials and can be used as an additional parameter in PMS. Specific relations between modulation frequency and synthesized material require further investigation.
R. Sabarish, N. Suriyanarayanan, J.M. Kalita, M.P. Sarma, G. Wary, Vipul Kheraj and Sampat G. Deshmukh
In this report, ternary semiconducting NixBi2−xS3(x = 0.2 M and 0.5 M) thin films were synthesized in situ for the first time by a chemical bath deposition technique at different bath temperatures (60 °C, 70 °C and 80 °C). The effects of concentration and deposition temperature on the deposited films were studied by combining the results of structural, morphological, optical and electrical analyses. The growth of NixBi2−xS3 films with good crystalline nature and interconnected grain arrangement takes place due to increasing the concentration of Ni2+ ions in bismuth sulfide matrix. EDS result confirmed the stoichiometry of NixBi2−xS3 formation. Wettability test demonstrated that the surface of the film was hydrophilic in nature. The optical absorption spectra revealed that the bandgap Eg of the x = 0.5 M film deposited at 70 °C was about 1.36 eV. Current-voltage (I-V) characteristics of the x = 0.5 M film deposited at 70 °C were studied under X-ray radiation and dark condition. An X-ray detection sensitivity analysis showed that the detection sensitivity is optimum when the bias voltage applied across the film is low (~0.9 V). These findings reveal that the film with x = 0.5 M deposited at 70 °C can be used as an efficient low cost X-ray sensor.
Amelitta Legendi, Laurențiu Rece, Andreea Dora Bianca Pironea and Virgil Florescu
In the process of preparing cement or asphalt concrete – frequently used in ways, roads and access road construction, it is necessary to sort out poly-dispersed granular mixtures from bilge deposits or quarries. The mechanical sieving performs the separation of the granules on dimensional sorts (the size of graded grains can be 1... 70 mm) by means of machines called screeners. In the case of vibrating screeners, the working body (the sieve) presents a vibratory movement that ensures a high productivity of the screening machine and a very good quality of the final products obtained. The article studies the productivity of the vibrating screen used in mineral aggregates sorting process obtained by different methods. In this regard, a pragmatic simplified formula called Pragma is proposed, a formula which was tested with good results in situ experiments done on a bi-mass vibrating screen in a pilot station.
Paper describes the procedure for developing academic programs which are properly aligned to the requirements of the knowledge-based economy. The paper also addresses the continuous quality improvement (CQI) process with the CQI loop closing on the program level and the course level. This process is needed to make continuous adjustments to an academic program, so that the program is always aligned to the constantly-changing needs of the economy. Paper also discusses the system of mutual dependency between the academic program and external partnership like local industry, secondary schools, local government, local community, regional business incubator center, other educational institutions, alumni and industrial advisory council. The ongoing collaboration with external partners allows the program to prosper and grow.
Today’s market determinants and most importantly, very dynamically changing customer requirements significantly shortened the product life cycle. This situation reflects in companies by common extension of the assortment offered and personalised serial production. The result of a flexible approach to market changes is the implementation of LEAN concept, which, both in terms of management and production aims to develop efficiency within an organisation, which will then enable quick and dynamic response to changes in the environment. The popularity of LEAN concept (in management and production) among managers comes from its universality and a wide range of instruments used to maximise the use of existing potential. The main assumptions of LEAN concept are aimed at the maximum use of an organisation’s resources, defining the activities necessary to execute an order and identifying the areas generating losses and then minimising them and eventually eliminating. LEAN concept is based on flagship-main tools for identification and modernisation of processes, the difficulty in using them results from the need to recognise and select the most effective ones that meet the expectations of a given organisation. The article presents issues related to the first stage of implementing LEAN concept in a company’s structures, i.e. identification of opportunities and selection of appropriate tools.
Imran Khan, S. Kalainathan, M.I. Baig, Mohd Shkir, S. Alfaify, H.A. Ghramh and Mohd Anis
Present investigation has been started to perform the comparative study of pure and glycine doped KH2PO4 (KDP) single crystals grown by most commercial slow solvent evaporation technique. The grown crystals were subjected to single crystal X-ray diffraction analysis to determine their structural parameters. The linear optical studies of pure and glycine doped KDP crystal have been undertaken within 200 nm to 1100 nm wavelength range by means of UV-Vis studies. The enhancement in second harmonic generation (SHG) efficiency of glycine doped KDP crystal has been determined using a standard Kurtz-Perry powder test. The dielectric measurements have been carried out to explore the impact of glycine dopant on dielectric constant and dielectric loss of KDP crystal. The surface growth habitat and etch pit density of glycine doped KDP crystal have been evaluated using the results of microscopic etching studies. In light of obtained results the suitability of glycine doped KDP crystal for device applications has been discussed.
The paper aims to identify possible methods for balancing the allocation of transport flow on modal subsystems in order to efficiently use the infrastructures and reduce the negative effects of today’s unbalance. The aspects of intermodal competition are reviewed, considering the economic concepts regarding the substitutability of transportation services, conformation degree to the perfect competition model and the nature of cross elasticity demand.
A top-down analysis over the whole infrastructure assembly is performed. The results, under the presumption of valid work hypothesis, indicated that for further analysis the set of networks transferring material flows can be assumed as disconnected from the other networks sets transferring energy, informational and values flows.
The second part of the paper develops, for that disconnected networks, a generalized cost optimization model for multimodal transportation, where the comfort and safety are accounted. Thus, the performance of the existing algorithms based only on trip length, trip duration and energy consumption can be significantly improved. Additionally, the author proposes three new independent types of modal analysis that allow end-users and companies involved in transport organization to optimize their modal choice and the whole transport process organization.
H. Mokhtari, M. Benhaliliba, A. Boukhachem, M.S. Aida and Y.S. Ocak
This work highlights some physical properties related to the influence of aluminum, tin and copper incorporation on nanostructured zinc oxide (ZnO:M; M:Al, Sn and Cu) thin films prepared by ultrasonic spray pyrolysis technique (USP) on glass substrate at 350±5 °C. For the as-grown layers, M- to Zn-ratio was fixed at 1.5 %. The effects of metal doping on structural, morphological, optical and electrical properties were investigated. X-ray diffraction pattern revealed that the as-prepared thin films crystallized in hexagonal structure with (0 0 2) preferred orientation. The surface topography of the films was performed by atomic force microscopy. AFM images revealed inhibition of grain growth due to the doping elements incorporation into ZnO matrix, which induced the formation of ZnO nanoparticles. Optical measurements showed a high transparency around 90 % in visible range. Some optical parameters, such as optical band gap, Urbach energy, refractive index, extinction coeffi-cient and dielectric constant were studied in terms of doping element. Particularly, dispersion of refractive index was discussed in terms of both Cauchy and single oscillator model proposed by Wemple and DiDomenico. Cauchy parameters and single oscillator energy E0 as well as dispersion energy Ed were calculated. Finally, electrical properties were investigated by means of electrical conductivity and Hall effect measurements. The measurements confirmed n type conductivity of the prepared thin films and a good agreement between the resistivity values and the oxidation number of doping element. The main aim of this work was the selection of the best candidate for doping ZnO for optoelectronics applications. The comparative study of M doped ZnO (M:Al, Sn and Cu) was performed. High rectifying efficiency of the Al/n-ZnO/p-Si/Al device was achieved and non-ideal behavior was revealed with n > 4.