Browse

91 - 100 of 1,127 items :

  • Materials Sciences, other x
Clear All
RPAS Satellite Communication Channel Based on IEEE 802.11b Standard

Abstract

Original models of RPAS communication channels based on IEEE 802.11b Standard, including both Base Station transmission within the Radio Line of Sight, and through the satellite using Beyond Radio Line of Sight, were built. Dependencies of the Bit Error Rate on the Signal-Noise Ratio for different payload data rates were obtained. Transponder nonlinearity and Base Station antenna diameter impact were analysed.

Open access
Ship Noise Level Analysis Based on the International Regulations

Abstract

The target of analyse was to determine the exposure levels to the staff on the vessel and ensure adequate measures are in place to minimize the exposure when necessary. Noise levels through the vessel will be compared to the noise code detailed in section 2 of this report. The measurement data results obtained at this survey will be analysed against the codes, as shown below. In addition, the measurement result table has the readings from 2007 during sea trials at the shipyard, Brodogradilište d.o.o. – Split. The analyse is to measure the exposure levels, through the accommodation and machinery spaces to determine the risk to staff working in these areas as well as making recommendations that could reduce the exposure levels.

Open access
Turbine Blade of Gas Turbine Engine Additional Unloading by Changing the Layout of the Gravity Centre of the Shroud Shelf

Abstract

The article describes the impact of the gas turbine engine low-pressure turbine blade shroud shelf on the blade profile stress position. Attention is focused directly on the impact of the location of the gravity centre of the shroud shelf on blade stress distribution at the three most critical points of the profile. The paper describes the details of the calculation and the required expressions provided, as well as the results of the calculation example with clear graphical dependencies.

Open access
Analysis of surface properties of Ti-Cu-Ox gradient thin films using AFM and XPS investigations

Abstract

The paper presents results of investigations on surface properties of transparent semiconducting thin films based on (Ti-Cu)oxide system prepared using multi-magnetron sputtering system. The thin films were prepared using two programmed profiles of pulse width modulation coefficient, so called V- and U-shape profiles. The applied powering profiles allowed fabrication of thin films with gradient distribution of Ti and Cu elements over the thickness of deposited layers. Optical investigations allowed determination of transparency of prepared films that reached up to 60 % in the visible part of optical radiation, which makes them attractive for the transparent electronics domain. Surface properties investigations showed that the surface of mixed (Ti-Cu)oxides was sensitive to adsorption, in particular to carbon dioxide and water vapor. Soft etching with argon ions resulted in surface cleaning from residuals, however, deoxidation of Cu-oxide components was also observed.

Open access
Bending fatigue strength coefficient the low carbon steel with impurities

Abstract

The article discusses the results of a study investigating the effect of the number of fine non-metallic inclusions (up to 2 μm in size) on the fatigue strength of structural steel during rotary bending. The study was performed on 7 heats produced in an industrial plant. Fourteen heats were produced in a 100 ton oxygen converter. All heats were subjected to vacuum circulation degassing.

Steel sections with a diameter of 18 mm were hardened and tempered at a temperature of 200, 300, 400, 500 and 600°C. The experimental variants were compared in view of the applied melting technology and heat treatment options. The heat treatments were selected to produce heats with different microstructure of steel, from hard microstructure of tempered martensite, through sorbitol to the ductile microstructure of spheroidite. The results were presented graphically, and the fatigue strength of steel with a varied share of non-metallic inclusions was determined during rotary bending. The results revealed that fatigue strength is determined by the relative volume of fine non-metallic inclusions and tempering temperature.

Open access
Characterization of CuO/n-Si heterojunction solar cells produced by thermal evaporation

Abstract

Copper(II) oxide (CuO) in powder form was evaporated thermally on the front surface of an n-Si (1 0 0) single crystal using a vacuum coating unit. Structural investigation of the deposited CuO film was made using X-ray difraction (XRD) and energy dispersive X-ray analysis (EDX) techniques. It was determined from the obtained results that the copper oxide films exhibited single-phase CuO properties in a monoclinic crystal structure. Transmittance measurement of the CuO film was performed by a UV-Vis spectrophotometer. Band gap energy of the film was determined as 1.74 eV under indirect band gap assumption. Current-voltage (I-V) measurements of the CuO/n-Si heterojunctions were performed under illumination and in the dark to reveal the photovoltaic and electrical properties of the produced samples. From the I-V measurements, it was revealed that the CuO/n-Si heterojunctions produced by thermal evaporation exibit excellent rectifying properties in dark and photovoltaic properties under illumination. Conversion efficiencies of the CuO/n-Si solar cells are comparable to those of CuO/n-Si produced by other methods described in the literature.

Open access
Context of production engineering in management model of Value Stream Flow according to manufacturing industry

Abstract

The popularity of visual management in the lean concept is caused by the possibility to apply it in solving different kind of issues related to reduce waste or process planning. The adaptations of VSM is focused on stream flow, identifying waiting and productive times in accordance to material and information flow. In this paper five basic areas of value stream flow management have been presented and characterized. Discussion under the 5 areas on the VSM process included identifying the dominant stream in the area and the range of factors affecting the flow of the stream. Based on an observation of processes in the manufacturing industry and a literature review, the graphic model of mutual cooperation between value stream areas (1-5) has been presented.

Open access
Development and Testing of Data Reduction Software for Measurements Using Pressure Sensitive Paints

Abstract

The paper concentrates on post-processing of data necessary for pressure measurements using Pressure Sensitive Paints (PSP). The purpose of the study was to develop and test procedures for extraction of the surface pressure distribution from the images captured during PSP tests. The core issues addressed were reduction of the influence of model movement and deformation during wind tunnel run and synchronization between conventional pressure tap measurements and PSP data, necessary for in-situ calibration. In the course of the studies, two approaches on image registration were proposed: the first based on geometric transformation of control points pairs with cross-correlation tuning and the second based on similarity finding and estimation of geometric transformation of the images. Performance of the developed algorithm was tested with use of experimental set-up allowing for controlled movement of the imagined target with micrometer resolution. Both of the proposed approaches to PSP image resection proved to perform well. After testing of the software, the PSP system was used for determination of the pressure field on flat plate exposed to impinging jet. The presented procedures and results can be useful for research groups developing in-house PSP measurements systems for wind tunnel tests and internal flow investigations.

Open access
Effect of MgB2 additives on structure, electrical and thermal properties of Eu1Ba2Cu3O7

Abstract

The effect of MgB2 addition on the Eu1Ba2Cu3O7 (EBCO) ceramics was systematically studied. Series of Eu1Ba2Cu3O7 + x(MgB2) samples (x = 0 wt.%, 0.05 wt.%, 0.1 wt.%, 1 wt.%, 3 wt.%) were prepared using traditional solid state method. X-ray powder diffraction measurements were used for phase identification. The lattice parameters and orthorombicity decreased with MgB2 addition. A standard four point measurement method was used to determine transition temperatures Tc of superconducting samples. Tc values of the samples were decreasing with MgB2 concentration. TGA results indicate thermal stability of doped samples.

Open access
Electrical and optical properties of new Pr3+-doped PbWO4 ceramics

Abstract

Polycrystalline samples of new scheelite-type tungstates, Pb1−3x xPr2xWO4 with 0.0098 ⩽ x ⩽ 0.20, where denotes cationic vacancies have been successfully prepared by a high-temperature solid-state reaction method using Pr2(WO4)3 and PbWO4 as the starting reactants. The influence of the Pr3+ substitution in the scheelite framework on the structure and optical properties of prepared new ceramic materials has been examined using powder X-ray diffraction method (XRD) and UV-Vis-NIR spectroscopy. The results of dielectric studies of Pb1−3x xPr2xWO4 samples showed both low values of dielectric constant (below 14) and loss tangent (below 0.2). The electrical conductivity and thermoelectric power measurements revealed a low conductivity (∼2 × 10−9 S/m) and the sign change of thermoelectric power around the temperature of 366 K suggesting the p-n transition. These results are discussed in the context of vacancy, acceptor and donor levels as well as the Maxwell-Wagner model.

Open access