Browse

1 - 10 of 284 items :

  • Geosciences, other x
Clear All
Influence of Humidity on the Energy of Specific Strain in the Process of Loading Sedimentary Rocks

Abstract

This article presents the results of tests on the energy properties of sedimentary rocks in the Upper Silesian Coal Basin. The rocks were tested both in an air-dry state and in a water saturation state. Samples of sedimentary rocks were collected from boreholes drilled in the underground workings of coal mines located within the area of the city of Jastrzębie, in the areas of the Chwałowice Trough and Rybnik Trough (south-western part of the Upper Silesian Coal Basin) and in the Main Trough. Influence of saturation condition on the values of the tested energy parameters was observed. The values of elastic energy and dissipated energy obtained for the samples tested in water saturation were lower compared to the values obtained for samples tested in air-dry state. As observed, an increase in the values of the given types of specific energy corresponds to an increase in the uniaxial compression strength in air-dry state and in water saturation state. Results of the tests are original and they can be applied while analysing the possibility of the occurrence of some dynamic phenomena and hazards in mine workings in Carboniferous rock mass in the Upper Silesian Coal Basin, caused by mining operations.

Open access
Setup of axial bearing capacity of open ended tubular steel piles driven in sand

Abstract

This paper focuses on the setup of axial bearing capacity of open ended tubular steel piles that are used for offshore foundation systems such as those of wind turbines. A comparative evaluation of the most commonly used models for setup prediction shows an upper estimate bound and a lower estimate bound, which correspond approximately to a setup rate of 60% increase per log cycle of time and 20% increase per log cycle of time, respectively. This finding is validated with the results of case histories reported in literature, which show that the setup values of most case histories considered lie in the best estimate zone between the upper estimate zone and the lower estimate zone. The analysis results show a minimum setup factor of approximately 1.5 for 100 days following end of driving of open-ended tubular steel pile driven in sand.

Highlights

  1. Detailed presentation of setup phenomenon in granular sand and contributing mechanisms
  2. Detailed presentation of setup prediction models in granular sand
  3. Demonstration of lower bound, best estimate bound and upper bound for setup prediction
  4. Compilation of case histories of setup for driven open ended pile in granular soil and validation of lower estimate, best estimate and upper estimate zone

Open access
Hydraulic Characterization of a Self-Weight Compacted Coal

Abstract

Water infiltration through coal stocks exposed to weather elements represents a key issue for many old mining sites and coal-fired power plants from the environmental point of view, considering the negative impact on human health of the deriving groundwater, soil and air pollution. Within this context, the paper investigates the hydraulic behaviour of a self-weight compacted unsaturated coal mass and its impact on the numerical prediction of infiltration induced by rainfall events. In particular, the work focuses on the experimental investigation carried out at different representative scales, from the grain scale to physical modelling. The material, when starting from uncompacted conditions, seems to be characterized by metastable structure, which tends to collapse under imbibition. In addition, direct numerical predictions of the seepage regime through a partially saturated coal mass have been performed. As the compaction of the coal stock induced by dozers has not been taken into account, the numerical simulations represent a conservative approach for the assessment of chemical pollution hazard associated to water infiltration into a real stockpile under operational conditions.

Open access
Modelling Of Rock Joints Interface Under Cyclic Loading

Abstract

The problem of numerical simulation of the material interface response under monotonic and cyclic loading is of fundamental scientific and engineering importance. In fact, such interfaces occur in most engineering and geotechnical structures. The present work is devoted to the deformational response analysis of contact interfaces under monotonic and cyclic loads. The class of materials includes rock and structural joints, soil structure interfaces, masonry and cementitious joints, localized shear bands and so on.

The aim of the proposed model is to simulate the cyclic shear test under constant normal load. The associated dilatancy effect is associated with the configurational effects of asperity interaction or dilatancy of wear debris layer. The large primary asperities are assumed as responsible for interfacial dilation and small size asperities as governing frictional sliding and hysteresis response. The elliptic loading yield function is assumed to translate and rotate during progressive or reverse loading events. The model formulation is discussed and confronted with experimental data.

Open access
Application of The New Shape Crushing Plate in Machine Crushing Processes

Abstract

The results of studies of the crushing process in a double toggle jaw crusher are presented. This process was carried out on six sets of crushing plates. The first three of them are used in industrial crushers – plates with a flat working surface and a triangular profile (in this work, under consideration were profiles with teeth angle γ = 90°). The fourth and fifth type refer to plates with a variable pitch t and teeth height with a triangular shape of the teeth. In the sixth solution, plates with variable pitch and width of the wedged teeth are proposed.

The results of the basic process parameters are shown, that is, average degree of fineness n, technical performance Wt, crushing energy L and crushing force F, sieve analysis of crushing product. The obtained results are the basis for the assessment of the suitability of various types of plates, especially plates with a new profile, which have an altered shape in comparison with the plates used in crushers so far.

The crushing tests were carried out with the same dimension of outlet slot er = 24 mm, close to the pitch size for plates with triangular profile. Tests were performed on the “Mucharz” sandstone. Samples from a series of blocks of different size and geometric shape were prepared. This work also presents feed mass influence on crushing process efficiency.

The plates with variable pitch and width of teeth are beneficial because of lower crushing force and energy.

Open access
2D numerical analysis of the seismic response of a karst rock mass: importance of underground caves and geostructural details

Abstract

The present study shows the results of a 2D local seismic response (LSR) analysis, simulated for a geomechanical model consisting of a layered carbonate rock mass with hypogean karst caves and a structural– lithostratigraphic complex setting, in an area within the Municipality of Turi (Apulia, Italy). In this case study a Distinct Element Code (DEM) code (UDEC) was used for the LSR simulations conducted on a model both in the absence and in the presence of two overlapping karst caves. The preliminary stress–strain model analysis show some tensile yielding points clustered on the roof of the upper karst cave, already in static conditions, and the phenomenon becomes even more noticeable in dynamic conditions. This is perfectly in agreement with the real occurrence of a sinkhole that brought to the light the underlying karst cave, in the case study area, in the recent past.

The amplification/deamplification factor (FA) was calculated as the ratio of the top value to the bottom value in the model, both of the max X-acceleration and of the spectral Fourier amplitude in three different ranges of frequencies, in order to estimate the effects of LSR on the X-component of the seismic input. According to the previous studies, the results obtained show a generalised deamplification of the seismic ground motion at the top of the model, both without and with underground karst caves, caused by the presence of the upper karst cave and by the seismic energy absorption because of layers’ discontinuity.

Open access
3D Numerical Modeling of Large Piled-Raft Foundation on Clayey Soils for Different Loadings and Pile-Raft Configurations

Abstract

In a piled-raft foundation, the interaction between structural elements and soil continuum can be simulated very precisely by numerical modeling. In the present study, 3D finite element model has been used to examine the settlement, load-sharing, bending moment, and shear force behavior of piled-raft foundation on different soil profiles for different load configurations and pile-raft configurations (PRCs). The model incorporates the pile-to-soil and raft-to-soil interactions by means of interface elements. The effect of parameters such as pile spacing and raft thickness are also studied. For any soil profile, larger pile spacing is observed to be more efficient in reducing the average settlement and enhancing the load-sharing coefficient. The smaller pile spacing is observed to be efficient in reducing the differential settlement. For any soil profile, the behavior of piledraft foundation is significantly affected by the PRCs and load configurations. Furthermore, the raft thickness has significant effect on settlement, bending moment, and shears force. Thus, the results of the present study can be used as guidelines for analyzing and designing large piled-raft foundation.

Open access
Shear strength of compacted Chlef sand: effect of water content, fines content and others parameters

Abstract

This paper presents a laboratory study of the combined effect of the water content and fines content on the mechanical behaviour of Chlef sand in a medium dense state (RD = 65%) and dense state (RD = 80%). Several mechanical parameters were evaluated such as shear strength, cohesion and friction angle at different water content w = 0, 1, 2 and 3% and different fines content Fc = 0, 10, 20, 30 and 40%. The test results showed that the shear strength of Chlef sand decrease with the increase fines content Fc = 0 to 40%, our tests result also showed that the water content has a significant influence on the shear strength which decreases with the increase in the water content w = 0 to 3%. The fines content and the water content have a significant influence on the mechanical parameters c and φ. Cohesion increases with the percentage of fines and decreases with the increase of the water content while the friction angle decreases with the increase the fines content and the water content.

Open access
Critical state constitutive models and shear loading of overconsolidated clays with deviatoric hardening

Abstract

This paper presents an enhanced constitutive model integrating deviatoric hardening with a modified yield surface for overconsolidated clayey soils in a general framework of Cam-clay type models. Its performance was assessed with the simulation of drained and undrained triaxial tests on three clays at different consolidation states in comparison to two critical state models. The proposed model satisfactorily estimates the shear resistance, while capturing the smooth nonlinearity of the soil response.

Shear triaxial tests at constant mean pressure were performed on an overconsolidated marl to study the shear response. Their simulation attests the importance of deviatoric hardening integration.

Open access
Analysis of crack propagation in a “pull-out” test

Abstract

The article describes a computer analysis of the pull-out test used to calculate the force needed to pull out a rock fragment and determine the shape of this broken fragment. The analyzed material is sandstone and porphyry. The analysis included the first approach to using own subroutine in the Simulia Abaqus system, that is, which task is undertaken to accurately determine the crack path of the Finite Element Method model. The work also contains a description of laboratory tests and analytical considerations.

Open access