The influence of the cutting attachment on vibrations emitted by brush cutters and grass trimmers

Open access


Generally, the choice of cutting attachment used in brush cutters for brushwoods and grasses depends on the type of work, on one hand, and the size of the engine, on the other. However, at the same time, the use of individually chosen cutting elements entails a certain risk of vibration resulting from their varying design and size, which has a big impact on comfort and working time, but most importantly on operator health.

The aim of the study is a preliminary analysis of the dangers due to vibration of brush cutters and to determine how the choice of the cutting attachment affects the intensity of the vibrations emitted by the machine. Furthermore, one aim was to determine the daily vibration exposure, relative to an equivalent value of vibration, experienced by the device operator.

This study involved four models of brush cutters with three machines of each model, differing in size (displacement and engine power) and equipped with six different cutting elements. A vibration acceleration test was carried out in accordance with the applicable PN-EN ISO 5349-1 and 2: 2004 and Directive 2002/44 / EC.

An analysis of the obtained results leads to the conclusion that the examined professional brush cutters emit vibrations of such intensity that the daily exposure limit (5 m s−2) is exceeded more than two-fold. One cannot directly determine the influence on vibration intensity by the type of cutting attachment or the exhaust, but it should be noted that use of a cutting unit as recommended by the manufacturer creates less harmful vibrations, especially when the engine runs at the nominal rotational speed. In order to minimise the risk due to vibrations from brush cutters, engines with a cylinder capacity below 45 cm3 are recommended to be equipped with trimmer heads and disk knives, while engines with over 50 cm3 should run with circular saws.

Bovenzi M., Franzinelli A., Mancini R., Cannavà M.G., Maiorano M., Ceccarelli F. 1995. Dose-response relation for vascular disorders induced by vibration in the fingers of forestry workers. Occupational and Environmental Medicine 52: 722–30. DOI: 10.1136/oem.52.11.722.

Christ E. 2002. Vibrationseinwirkung am Arbeitsplatz – Gefährdungsbeurteilung und Prävention. Die BG. Heft 5.

Dyrektywa 2002/44/WE Parlamentu Europejskiego i Rady z dnia 25 czerwca 2002 r.. w sprawie minimalnych wymagań w zakresie ochrony zdrowia i bezpieczeństwa dotyczących narażenia pracowników na ryzyko spowodowane czynnikami fizycznymi (wibracji).

Hao K.Y., Ripin Z.M. 2013. Nodal control of grass trimmer handle vibration. International Journal of Industrial Ergonomics 43(1): 18–30. DOI: 10.1016/j.ergon.2012.10.007.

Ishikawa D., Miyakawa S., Oono T., Yamamoto T., Kawano T. 2013. Experimental verification on mitigation of mowing work of yajirobe type brush cutter. Ergonomics 49: 236–237.

Kashima J., Uemura T. 2010. Analysis of accidents related to brush cutter use. Journal of the Japan Forest Engineering Society 25(2): 77–84.

PN-EN ISO 5349-1: 2004. Drgania mechaniczne. Pomiar i wyznaczanie ekspozycji człowieka na drgania przenoszone przez kończyny górne. Część 1: Wymagania ogólne.

PN-EN ISO 5349-2: 2004. Drgania mechaniczne. Pomiar i wyznaczanie ekspozycji człowieka na drgania prezenoszone przez kończyny górne. Część 2: Praktyczne wytyczne do wykonywania pomiarów na stanowisku pracy.

PN-EN ISO 11806-1: 2012E. – Maszyny rolnicze i leśne. Wymagania bezpieczeństwa i ich sprawdzanie dla kos spalinowych do zarośli i trawy. Część 1: Maszyny napędzane zintegrowanym slinikiem spalinowym.

Okada S., Nakano M., Kikuchi Y., Matsuda I., Yuasa K., Nitta S. 2009. Study on low vibration brush cutter. JSME Industrial. Chemical Machinery & Safety Division Conference. 23–24.

Rajbhandary P., Leifer J., Weems B.J. 2011. Reduction of Vibration Transmission in String Trimmers. in: Rotating Machinery. Structural Health Monitoring. Shock and Vibration. Volume 5. Conference Proceedings of the Society for Experimental Mechanics Series 8 (ed. T. Proulx). 129–138. DOI: 10.1007/978-1-4419-9428-8_10.

Więsik J., Wójcik K., Kozłowki R., Naugebauer Z. 2005. Pilarki przenośne – budowa i eksploatacja. Warszawa. SGGW. ISBN 83-7274-067-4.

Yoshida J., Uemura M., Miyakawa S., Oono T., Ishikawa D. 2013. Reduction of high frequency vibration of brush cutter by structure optimization. London. Proceedings of the World Congress on Engineering Volume III. ISBN 978-988-19252-9-9.

Forest Research Papers

Lesne Prace Badawcze; The Journal of Forest Research Institute, Sekocin Stary

Journal Information


All Time Past Year Past 30 Days
Abstract Views 0 0 0
Full Text Views 238 235 14
PDF Downloads 256 254 17