Compaction Behaviour Modelling of Metal-Ceramic Powder Mixtures. A Review

Open access

Abstract

Powder mixtures compaction behavior can be quantitatively expressed by densification equations that describe the relationship between densities - applied pressure during the compaction stages, using correction factors. The modelling of one phase (metal/ceramic) powders or two-phase metal-ceramic powder composites was studied by many researchers, using the most commonly compression equations (Balshin, Heckel, Cooper and Eaton, Kawakita and Lüdde) or relative new ones (Panelli - Ambrózio Filho, Castagnet-Falcão- Leal Neto, Ge Rong-de, Parilák and Dudrová, Gerdemann and Jablonski. Also, for a better understanding of the consolidation process by compressing powder blends and for better prediction of compaction behavior, it's necessary the modeling and simulation of the powder pressing process by computer numerical simulation. In this paper are presented the effect of ceramic particles additions in metallic matrix on the compressibility of composites made by P/M route, taking into account (a) the some of above mentioned powder compression equations and also (b) the compaction behavior modeling through finite element method (FEM) and discrete element modeling (DEM) or combined finite/ discrete element (FE/DE) method.

If the inline PDF is not rendering correctly, you can download the PDF file here.

  • [1] R. W. Heckel A normalized density-pressure Curve for Powder Compaction Trans. Metall. Soc. AIME 224 (1962). 1074.

  • [2]. I. H. Moon K. H. Kim Relationship between compacting pressure green density and green strength of copper powder compacts Powder Met. 27( 2) (1984). 80-84.

  • [3] T. Çomoğlu An Overview of Compaction Equations J. Fac. Pharm Ankara 36 (2) (2007)123-133.

  • [4] C. Cazotti J.L.A. Oliveira J.B. Fogagnolo Efeito da Adição de Partículas de Al2O3 sobre a Compressibilidade de Pós De Ligas De Alumínio 17o Proceedings of CBECIMat 15 -19 de November Foz do Iguaçu PR Brasil (2006) 7452.

  • [5] R. Panelli Thesis Coordinator Prof. Dr. Ambrosio Fillo Production of AISI M2 + 10%Vol. NbC by Mechanical Alloying Sao Paulo 1999.

  • [6] S. Mani L.G. Tabil and S. Sokhansanj Evaluation of compaction equations applied to four biomass species Canadian Biosystems Engineering/Le génie des biosystèmes au Canada 46(2004) 3.55-3.61.

  • [7]Luciano José De Oliveira Thesis Processing and Characterization of the Fe-Cu-Diamond System for Diamond Wire Pearls Use (in Portugues) Univ. de Estadual do Norte Fluminense 2005.

  • [8] M. Castagnet R. B. Falcão R. M. Leal Neto Compressibility Evaluation Of Mechanically Activated Niobium And Aluminum Powders Mixtures 18º CBECiMat - 24 a 28 de Novembro de 2008 Porto de Galinhas PE Brasil 6785.

  • [9] S.J. Gerdemann and P.D. Jablonski Compaction of Titanium Powders . Metall. Mater. Trans. A 42A (2011).1325-1333.

  • [10] Ge Rong-de A New Powder Compaction Equation The International Journal of Powder Metallurgy 27 (3) (1991).211-214.

  • [11] L. Parilák E. Dudrová R. Bidulský M. Kabátová Quantification of Metal Powder Compressibility in Uniaxial Compaction Metallurgy World Congress and Exhibition. Euro PM 2004. Vol. 1. Vienna 17.-21.10.2004. Ed. H. Danninger R. Ratzi EPMA 2004 p. 593-598

  • [12] H. Hafizpour A. Simchi S. Parvizi Analysis of the compaction behavior of Al-SiC nanocomposites using linear and non-linear compaction equations Advanced Powder Technology 21(3) (2010) 273.

  • [13] A. Miskova E. Dudrova H. Brunckova M. Faberova R. Bures Compressibility of Fe/SiO2 Coated Composite Powders PM2010 World Congress - Fundamentals of Pressing p. 39

  • [14] R. Bureš M.Fáberová Evaluation of Compressibility of Micro-Composite Systems PM2010 World Congress - Compaction Equipment p.81

  • [15]S. Sivasankaran K. Sivaprasad R. Narayanasamy V. K. Iyer Evaluation of compaction equations and prediction using adaptive neuro-fuzzy inference system on compressibility behavior of AA 6061 100− x-x wt.% TiO 2 nanocomposites prepared by mechanical alloying Powder Technol. 209 (1) (2011).124.

  • [16]. M. Moreno C. G. Oliver Densification of al powder and Al-Cu matrix composite (reinforced with 15% saffil short fibres) during axial cold compaction Powder Technol. 206(3) (2011).297.

  • [17] C. Machio R. Machaka T. Shabalala H. K. Chikwanda Analysis of the Cold Compaction Behaviour of TiH2-316L Nanocomposite Powder Blend Using Compaction Models Materials Science Forum 828-829 (2015).121.

  • [18] C.A. Leon G. Rodriguez-Ortiz E.A. Aguilar-Reyes Cold compaction of metal-ceramic powders in the preparation of copper base hybrid materials Materials Science and Engineering A 526 (2009).106.- [19] C. Ghiţă I.N. Popescu Experimental research and modelling of compaction behaviour of Al based composite with SiC particles Comp Mater Sci 64 (2012) 136-140.

  • [20] S.Sivasankaran PhD Thesis Coordinator Prof. Dr. R.Narayanasamy Study on Synthesis Characterization and Workability behavior of nanocrystalline AA6061 alloy reinforced with TiO2 Composite prepared by Mechanical alloying NITTiruchirappalli.

  • [21] R. Machaka and H. K. Chikwanda An Experimental Evaluation of The Gerdemann-Jablonski Compaction Equation Metall Mater Trans A 46 (5) (2015).2194

  • [22] I.N. Popescu R. Vidu Compaction of Metal - Ceramic Powder Mixtures. Part. 1 ARA Journal of Sciences old ISSN 0896-1018 in press.

  • [23] I.N. Popescu R. Vidu Compaction of Metal - Ceramic Powder Mixtures. Part. 2 ARA Journal of Sciences old ISSN 0896-1018 in press.

  • [24] Cardei Petru Gageanu Iuliana A Critical Analysis ofEmpirical Formulas Describing The Phenomenon of Compaction of the Powders J. Modern Technology & Engineering 2(1) (2017).1-20

  • [25] P. Han X. Z. An Y. X. Zhang Z. S. Zou FEM Modeling on the Compaction oF Fe and Al Composite Powders J. Min. Metall. Sect. B-Metall. 51 (2) B (2015) 163 - 171

  • [26] Sinka I.C. Modelling Powder Compaction Kona-Powder and Particle 25 (2007) 4-22.

  • [27] D. Poquillon J. Lemaitre et.al. Cold compaction of iron powders-relations between powder morphology and mechanical properties Part I: Powder preparation and compaction Powder Technology 126 (2002) 65- 74.

  • [28] Rusanescu C.O Jinescu C Rusanescu M. Enescu M. C. Anghelina F. V. Stoian E. V. Despa V. Mathematical Modelling of the Stress-Strain Curve for 31VMn12 Ecological Steel Materiale Plastice 54 ( 3) (2017) 409-413.

  • [29] Faruk Güner Ömer Necati Cora Hasan Sofuoğlu Numerical modeling of cold powder compaction using multi particle and continuum media approaches Powder Technology 271 (2015) 238-247.

  • [30] C.L. Martin D. Bouvard Study of the cold compaction of composite powders by the discrete element method Acta Materialia 51 (2003) 373-386

  • [31] Harthong Barthelemy; Jerier Jean-Francois; Richefeu Vincent; et al. Contact impingement in packings of elasticplastic spheres application to powder compaction International Journal of Mechanical Sciences 61 (1 ) (2012) 32-43

  • [32] Harthong Barthelemy; Imbault Didier; Doremus Pierre The study of relations between loading history and yield surfaces in powder materials using discrete finite element simulations Journal of the Mechanics and Physics of Solids 60 (4) 2012 784-801

  • [33] Jerier J-F; Hathong B.; Richefeu V.; et al. Study of cold owder compaction by using the discrete element method Conference: Symposium STPMF 2009 Montpellier FRANCE MAY 25-27 2009 Powder Technology 208 (2) SI 537-541.

  • [34] Fen Huang Xizhong An; Yuxi Zhang et al. Multi-particle FEM simulation of 2D compaction on binary Al/SiC composite powders 1st International Workshop on Computational Particle Technology Suzhou Peoples R China Powder Technology 314 SI (2016) 39-48.

  • [35] Goran Frenning Compression mechanics of granule beds: A combined finite/discrete element study Chemical Engineering Science 65 (8 ) (2010) 2464-2471.

  • [36]Goran Frenning An efficient finite/discrete element procedure for simulating compression of 3D particle assemblies Computer Methods In Applied Mechanics And Engineering 197 (49-50) (2008). 4266-4272.

  • [37] DT Gethin RS Ransing RW Lewis et al. Numerical comparison of a deformable discrete element model and an equivalent continuum analysis for the compaction of ductile porous material COMPUTERS & STRUCTURES 79 ( 13) (2001). 1287-1294.

  • [38] K. T. Kim J. H. Cho Cold Compaction of Composite Powders J. Eng. Mater-T. Asme. 122 (2000) 119-128.

  • [39] K. T. Kim J. H. Cho A densification model for mixed metal powder under cold compaction Int. J. Mech. Sci. 43 (2001)2929-2946

  • [40] A. Kadir Eksi et.al Experimental and numerical studies of metallic powders subjected to cold isostatic pressing International Journal of Materials Research 102 (5) (2011) 572.

  • [41] Erik Olsson PhD Thesis Micromechanics of Powder Compaction Royal Institute of Technology Stockholm 2015.

  • [42] S. Shima M. Oyane Plasticity theory for porous metals Int. J. Mech. Sci. 18 (1976) 285- 291

  • [43] A. L. Gurson Continuum Theory of Ductile Rupture by Void Nucleation and Growth: Part I-Yield Criteria and Flow Rules for Porous Ductile Media ASME J. Eng. Mater. Technol. 99 (1977) 2-15.

  • [44] M. F. Moreno C. J. R. González Oliver Densification of Al powder and Al-Cu matrix composite (reinforced with 15% Saffil short fibres) during axial cold compaction Powder. Technol. 206 (2011) 297-305.

  • [44] A. K. Eksi A. H. Yuzbasioglu Effect of sintering and pressing parameters on the densification of cold isostatically pressed Al and Fe powders.Mater. Design 28(4) (2007) 1364..

  • [45]W. Wu G. t. al. Experimental and numerical investigation of idealized consolidation: Part 1:Static compaction Acta Mater. 48 (2000) 4323-4330.

  • [46] D. Gethin A.K. Arin D.V. Tran R.W Lewis Compaction and Ejection of Green Powder Compacts Powder Metallurgy 37(1) (1994) 42-54.

  • [47] T. Sheppard H.B.McShane Strength of Cold-Pressed Compacts Powder Metallurgy 23 (3).(1980) 120-124.

  • [48] F. Fischmeister HE. Arzt Powder Metallurgy Densifcation of Powders by Particle Deformation 26(2) (1983) 82-88.

  • [49] I.N. Popescu S. Zamfir F. V.Anghelina C.O. Rusǎnescu Fabrication through P/M of ecological aluminum based composite materials. Part 1-Characterization and densification of mixture powders Proceedings of the 2nd Int. Conference on MEQAPS Constantza Sep 03- 05(2010) 200-205.

  • [50] Amir R. Khoei Computational Plasticity in Powder Forming Processes Elsevier Publisher 2005.

Search
Journal information
Metrics
All Time Past Year Past 30 Days
Abstract Views 0 0 0
Full Text Views 315 182 11
PDF Downloads 341 276 23