Disk Laser Welding of Armor Steel/ Spawanie Laserem Dyskowym Stali Pancernej

Open access

Abstract

The paper describes the application of an Yb:YAG disk laser with a maximum output of 3.3 kW for the butt welding of armor steel plates ARMOX 500T 3.6 mm thick. The influence of laser welding parameters such as laser power beam, welding speed, focal point position on weld quality and mechanical properties of joints was studied. A proper selection of disk laser welding parameters provides non-porous and cracks free fully-penetrated welds with the aspect ratio up to 6.4. There was approx. 40% reduction in the hardness of heat affected zone (HAZ) in comparison to hardness of the base material (BM). The hardness values at the weld metal and the BM were similar. The joints exhibited about 15% lower ultimate tensile strength when compared with that of the BM. Charpy absorbed energy of the joints was approx. 30% lower than that of the BM.

[1] I. Barenyi, O. Hıres, P. Lip, Changes in Mechanical Properties of Armoured UHSLA Steel ARMOX 500 After Over Tempering. Problems of Mechatronics Armament, Aviation, Safety Engineering (14), 7-14 (2013).

[2] G. Magudeeswaran, et al., Effect of welding consumables on tensile and impact properties of shielded metal arc welded high strength, quenched and tempered steel joints. Journal of iron and steel research, international 15, 87-94 (2008).

[3] T. Borvik, S. Dey, A.H. Clausen, Perforation resistance of five different high strength steel plates subjected to small arm projectiles. Int J of Impact Eng 36, 948-964 (2009).

[4] S.J. Alkemade, The Weld Cracking Susceptibility of High Hardness Armour Steel. Australia: Defence Science and Technology Organization, 1996.

[5] D. Wojnowski, Y.K. Oh, J.E. Indacochea, Metallurgical Assessment of the Softened HAZ Region During Multipass Welding Journal of Manufacturing Science and Engineering 122(2), 310 (2000).

[6] G. Madhusudhan, et al., Effect ofWelding Process on the Ballistic Performance of HighStrength Low-Alloy Steel Weldments. Journal of Materials Processing Technology 74(1-3), 27 (1998).

[7] A. Lisiecki, Diode laser welding of high yield steel’, Proc.of SPIE, 8703, Laser Technology 2012: Applications of Lasers, 22 January 2013, 223-234.

[8] D. Janicki, Fiber laser welding of nickel based superalloy Inconel 625’, Proc. SPIE, Laser Technology 2012: Applications of Lasers, 2013, 8703, 87030R, doi: 10.1117/12.2013430.

[9] A. Lisiecki, Welding of titanium alloy by Disk laser. Proc. of SPIE 8703, Laser Technology 2012: Applications of Lasers, 87030T (January 22, 2013).

[10] W. Burian, J. Marcisz, B. Garbarz, L. Starczewski, Nanostructured Bainite-Austenite Steel for Armours Construction, Arch. Metall. Mater. 59(3), 1211-1216 (2014).

[11] A. Grajcar, M. Rózanski, M. Kaminska, B. Grzegorczyk, Study on Non-Metallic Inclusions in Laser-Weided TRIP-Aided Nb-Microalloyed Steel, Arch. Metall. Mater. 59(3), 1163-1169 (2014).

Archives of Metallurgy and Materials

The Journal of Institute of Metallurgy and Materials Science and Commitee on Metallurgy of Polish Academy of Sciences

Journal Information


IMPACT FACTOR 2016: 0.571
5-year IMPACT FACTOR: 0.776

CiteScore 2016: 0.85

SCImago Journal Rank (SJR) 2016: 0.347
Source Normalized Impact per Paper (SNIP) 2016: 0.740

Cited By

Metrics

All Time Past Year Past 30 Days
Abstract Views 0 0 0
Full Text Views 121 121 15
PDF Downloads 70 70 11