In order to increase wear resistance cast steel casting the TiC-Fe-Cr type composite zones were fabricated. These zones were obtained by means of in situ synthesis of substrates of the reaction TiC with a moderator of a chemical composition of white cast iron with nickel of the Ni-Hard type 4. The synthesis was carried out directly in the mould cavity. The moderator was applied to control the reactive infiltration occurring during the TiC synthesis. The microstructure of composite zones was investigated by electron scanning microscopy, using the backscattered electron mode. The structure of composite zones was verified by the X-ray diffraction method. The hardness of composite zones, cast steel base alloy and the reference samples such as white chromium cast iron with 14 % Cr and 20 % Cr, manganese cast steel 18 % Mn was measured by Vickers test. The wear resistance of the composite zone and the reference samples examined by ball-on-disc wear test. Dimensionally stable composite zones were obtained containing submicron sizes TiC particles uniformly distributed in the matrix. The macro and microstructure of the composite zone ensured three times hardness increase in comparison to the cast steel base alloy and one and a half times increase in comparison to the white chromium cast iron 20 % Cr. Finally ball-on-disc wear rate of the composite zone was five times lower than chromium white cast iron containing 20 % Cr.
 Bouaziz, O., Allain, S., Scott, C.P., Cugy, P. & Barbier, D. (2011). High manganese austenitic twinning induced plasticity steels: A review of microstructure properties relationship. Current Opinion in Solid State and Materials Science. 15(4), 141-168.
 Hu, S.W., Zhao, Y.G., Wang, Z., Li, Y.G. & Jiang, Q.C. (2013). Fabrication of in situ TiC locally reinforced manganese steel matrix composite via combustion synthesis during casting. Materials and design. 44, 340-345.
 La, P., Wei, F., Hu, S., Li, C. & Wei, Y. (2013). White cast iron with a nanoeutectic microstructure and high tensile strength and considerable ductility prepared by an aluminothermic reaction casting. Materials Science and Engineering A. 561, 317-320.
 Olejnik, E., Sikora, G., Sobula, S., Tokarski, T. & Grabowska, B. (2014). Effect of compaction Pressure applied to TiC reactants on the Microstructure and Properties of Composite Zones Produced in situ in steel castings. Materials Science Forum. 782, 527-532.
 Dolata, A.J. (2014). Centrifugal castings locally reinforced with porous Al2O3 preform. Archives of Metallurgy and Materials. 59(1), 345-348.
 Fengjum, C. & Yisan, W. (2007). Microstructure of Fe-TiC surface composite produced by cast sintering. Materials Letters. 61, 1517-1521.
 Olejnik, E., Sobula, S., Tokarski, T. & Sikora G. (2013). Composite zones obtained by in situ synthesis in steel castings. Archives of Metallurgy and Materials. 58, 769-773.
 Yang, Y. Wang, H., Liang, Y. & Jiang, Q. (2007). Fabrication of steel matrix composite locally reinforced with different ratios of TiC/TiB2 particulates using SHS reactions of Ni-Ti-B4C and Ni-Ti-B4C-C systems during casting. Materials Science and Engineering A. 445-446, 398-404.
 Merzhanov, A.G. (1996). Combustion processes that synthesize materials. Journal of materials processing technology. 56, 222-241.
 Fraś, E., Olejnik, E., Janas, A. & Kolbus, A. (2010). Fabrication of in situ composite layer on cast steel. Archives of Foundry Engineering. 10, 175-180.
 Fraś, E., Wierzbiński, S., Janas, A. & Lopez, H.F. (2002). Strength and plastic flow in “in situ” TiC reinforced aluminum composites. Metallurgical and Materials Transactions A. 33A, 3831–3838.
 Wang, Y., Zhang, Z.Q., Wang, H.Y., Ma, B.X. & Jiang, Q.C. (2006). Effect of Fe content in Fe-Ti-B system on fabricating TiB2 particulate locally reinforced steel matrix composite. Materials Science and Engineering. 422, 339-345.
 Tjong, S.C. & Ma, Z.Y. (2000). Microstructural and mechanical characteristic of in situ metal matrix composites. Materials Science Engineering. 29, 49-113.
 Liang, Y,. Zhao, Q., Zhang, Z., Li, X. & Ren, L. (2014). Preparation and characterization of TiC particulate locally reinforced steel matrix composites from Cu- Ti- C system with various C particles. Journal of Asian Ceramic Societies. 2, 281-288.
 Wang, H.Y., Jiang, Q.C., Ma, B.X., Wang, Y. & Zhao, F. (2005). Reactive infiltration synthesis of TiB2-TiC particulates reinforced steel matrix composite. Journal of Alloys and Compounds. 391, 55-59.
 Feng, K., Yang, Y., Shen, B. & Guo, L. (2005). In situ synthesis of TiC/Fe composites by reaction casting. Materials and Design. 26, 37-40.
 Yang, Y.F., Wang, H.Y., Liang, Y.H., Zhao, R.Y. & Jiang, Q.C. (2008). Effect of C particle size on the porous formation of TiC particulate locally reinforced steel matrix composites via the SHS reaction of Ni-Ti-C system during casting. Materials Science and Engineering. 474, 355-362.
 Song, M.S., Zhang, M.X., Zhang, S.G., Huang, B. & Li, J.G. (2008). In situ fabrication of TiC particulates locally reinforced aluminum matrix composites by self-propagating reaction during casting. Materials Science and Engineering. 473, 166-171.