The paper presents the results of simulation of alloy layer formation process on the model casting. The first aim of this study was to determine the influence of the location of the heat center on alloy layer’s thickness with the use of computer simulation. The second aim of this study was to predict the thickness of the layer. For changes of technological parameters, the distribution of temperature in the model casting and temperature changes in the characteristic points of the casting were found for established changes of technological parameters. Numerical calculations were performed using programs NovaFlow&Solid. The process of obtaining the alloy layer with good quality and proper thickness depends on: pouring temperature, time of premould hold at the temperature above 1300°C. The obtained results of simulation were loaded to authorial program Preforma 1.1 in order to determine the predicted thickness of the alloy casting.
 Fraś, E., Olejnik, E., Janas, A. & Kolbus, A. (2010). The morphology of TiC carbides produced in surface layers of carbon steel castings. Archives of Foundry Engineering. 10(4), 39-42.
 Fraś, E., Janas, A., Kolbus, A. & Olejnik, E. (2009). Cast in situ composites of Ni3Al / MeC type. Archives of Foundry Engineering. 19(2), 81-86.
 Fraś, E., Olejnik, E., Janas, A. & Kolbus, A. (2010). Fabrication of in situ composite layer on cast steel. Archives of Foundry Engineering. 10(spec. 1), 175-180.
 Mierzwa, P., Olejnik, E. & Janas, A. (2012). Nowoczesne materiały kompozytowe zastępujące tradycyjne materiały odlewnicze. Archives of Foundry Engineering. 12(spec. 1), 137-142.
 Olejnik, E., Janas, A., Kolbus, A. & Grabowska, B. (2011).Composite layers fabricated by in situ technique in Iron castings. Composites Theory and Practice. 2, 120-124.
 Janas, A., Kolbus, A. & Olejnik, E. (2009). On the character of matrix-reinforced particle phase boundaries in MeC and MeB (Me = W, Zr, Ti, Nb, Ta) in-situ composites. Archives of Metallurgy and Materials. 54(2), 319-327.
 Major, B., Mróz, W., Wierzchoń, T., Waldhauser, W., Lackner, J. & Ebner, R. (2004). Pulsed laser deposition of advanced titanium nitride thin layers. Surface and Coatings Technology. 180-181, 580-584.
 Asano, K. & Yoneda, H. (2008). Formation of In Situ Composite Layer on Magnesium Alloy Surface by Casting Process. Materials Transactions. 49(10), 2394-2398.
 Wróbel, T. (2011). Ni and Cr base layers in bimetallic castings. Metal 2011. International Conference on Metallurgy and Materials. Brno. 758-764.
 Janerka, K., Bartocha, D., Szajnar, J. & Jezierski, J. (2010).The carburizer influence on the crystallization process and the microstructure of synthetic cast iron. Archives of Metallurgy and Materials. 55(3), 851-859.
 Bartocha, D., Janerka, K. & Suchoń., J. (2005). Charge materials and technology of melt and structure of gray cast iron. Archives of Metallurgy and Materials. 162, 465-470.
 Szajnar, J., Bartocha, D., Baron, C. & Walasek, A. (2008).The attempt of determination of parameters for the alloy layer forming process based on the empirical examination.Archives of Foundry Engineering. 8(3), 139-143.
 Walasek, A. & Szajnar, J. (2012). The Mechanism of the Surface Alloy Layer Creation for Cast Steel. Archives of Foundry Engineering. 12(1), 115-118. DOI: 10.2478/v10266 -012-0022-0
 Szajnar, J., Walasek, A. & Baron, C. (2013). The zone without carbon in alloy layer obtained on steel cast.Manufacturing Technology. 13(1), 103-108.
 Baron, C., Bartocha, D. & Szajnar, J. (2008). The determination of the composite layer thickness with the use of software NovaFlow&Solid and Preforma 1.1. Archives of Foundry Engineering. 1(1), 5-12.